All Products

SKU: AF-653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: AF-1871

A sewable breakout board with a CR2032 coin cell battery holder, built-in on/off switch, and 0.1" pitch breakout pins. The board provides two ground pins, one switched power pin, and one always-on power pin — giving you flexibility in how you manage power in your project. Also available: version...

SKU: AF-1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: AF-783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: SF-DEV-08822

A 20 mm coin cell battery holder designed for CR2032 batteries. The holder features a pop-in, pop-out mechanism for easy battery changes, and the mounting feet include small holes for sewing onto fabric — making it suitable for e-textile and wearable electronics projects as well as standard PCB u...

SKU: AF-1285

The Adafruit Beginner LED Sewing Kit has everything you need to start stitching glowing circuits with conductive thread. No soldering or microcontroller required — the included candle-flicker LEDs twinkle automatically for a warm, animated glow. With enough supplies for two projects with two LED...

SKU: AF-1850

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a coin cell battery holder — everything you need to start sewing glowing electronic...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: AF-67

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...

SKU: KI-2746

When using through hole LEDs it can be hard to form the eyelets and then work out which leg is positive and negative. That's where these Sewable LED Holders come in! The 5mm LED holder boards, quickly and easily take any through hole 5mm LED and (after soldering in place) make them easy to use in...

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: AF-654

A standard CR2032 lithium coin cell battery providing 3V nominal output. This non-rechargeable cell is widely used in electronics projects, wearables, and sewable circuits. Specifications Type – CR2032 lithium coin cell (non-rechargeable) Nominal Voltage – 3V (starts at ~3.2V, drifts to ~2.5V...

SKU: LB-LR0309-20

A simple single-slot 9V battery holder case with wire leads for soldering or connecting directly to your projects. Keeps your battery secure and organised. Key Features Wire Leads – Pre-attached cables for direct soldering or breadboard connection Snap-Fit Design – Holds one standard 9V batte...

SKU: PI-TEK002

A tiny, vibrating motor, easily attachable to paper or fabric! Just connect 3-5V across it, polarity doesn't matter, and it'll BUUUUZZZZZZ!!! The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may damage the Teknikio LED boards, so please ONLY...

SKU: AF-248

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells for 7.2V at ~2000mAh. The 9V alkaline output is ideal for boards with a 5V volta...

SKU: AF-1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3x...

SKU: DF-FIT0538 · MPN: FIT0538

This battery holder takes two 18650 lithium cells and connects them internally in series for a standard 7.4 V output. It is a simple way to power electronics projects from common 18650 cells, such as those used in laptop battery packs and power banks.The holder includes a DC 2.1 power jack, makin...

SKU: LB-EAGLED-BUZZ

EagLED is Little Bird Electronics' wearable development kit. It's a complete Arduino compatible microcontroller that has LEDs, Light Sensor, Push Button and Buzzer built into a snippable board. USB Support The EagLED has built-in USB support that user can use to program and power up the boar...

SKU: LB-EAGLED-LED-O

EagLED LEDs are purpose-built for e-textiles and wearable projects. This pack of 10 orange sewable LEDs come attached to each other on a snappable strip — simply break them apart as needed and sew them into clothing, accessories, or whatever you can dream up. Made in Australia, they're a cost-eff...