All Products

SKU: DF-DFR0492

DFRobot FireBeetle series are low power consumption microcontrollers designed for Internet of Things (IoT) development. This Bluetooth controller combines Bluetooth Low Energy 4.1 with Arduino controller, offering functions similar to the former Bluno series but with lower power consumption. ...

SKU: DF-DFR1247 · MPN: DFR1247

This smart UPS expansion board adds battery-backed power management to the LattePanda IOTA, giving portable and embedded builds a laptop-like uninterruptible power supply. It uses the standard HID-UPS protocol, so Windows 10 and Windows 11 can recognise it as a battery device without drivers or c...

SKU: PL-1100

A Pololu micro metal gearmotor with a 5:1 gear ratio and low-power (LP) 6V motor. The LP motor variant uses precious metal brushes and draws the least current of the micro metal gearmotor family, making it well-suited for battery-powered projects where efficiency matters more than peak torque. A...

SKU: AF-3877

A hex Schmitt-trigger inverter IC that doubles as a handy logic level shifter. The 74AHCT14 provides six independent inverter channels, each with Schmitt-trigger inputs for clean switching on noisy or slow-transitioning signals. Spec'd for 5V operation but works at 3V as well. High-level inputs ...

SKU: LB-LR0214-142A

One input: DC 6V - 12V (input voltage to the output voltage must be higher than 1V.) Output: 3.3V (+ - 0.05v error), 5.0V (+ - 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly converter to the output) PCB board size: 4.5cm * 4.5cm With red power indicator le...

SKU: DF-DFR0123

This 20W adjustable DC-DC boost converter with a digital display is based on the professional boost chip and supports 3~32V power input, 5~35V output, and an accuracy of ±0.05V. The switching frequency is 400KHz, the conversion efficiency can reach 94%, it has the functions of overheating prote...

SKU: AF-3428

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually the battery runs down, and goes below 3.3V, so the voltage to the ESP8266...

SKU: DF-DRI0035

INTRODUCTION This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper motors (up to 2A per motor coil, 40V max). This stepper mo...

SKU: DF-SER0046

A 9g micro servo with an extended 270° rotation range, metal gears, and built-in analog feedback (0–3.3V). The wider rotation range makes it suitable for applications requiring more travel than a standard 180° servo, while the analog feedback signal enables closed-loop position control via an MCU...

SKU: AF-1374

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor.When a capacitive load is detected (e.g. a person touches the sensor-pad area...

SKU: SF-DEV-21247

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, digital cameras, Bluetooth dongles, game controllers, and more. This version up...

SKU: DF-DFR0625

ESP32-PICO-KIT is a mini IoT development board with functionalities of WiFi and Bluetooth. With a size of 52x 20.3x10mm, the module integrates a 4 MB SPI flash, and a USB-UART Bridge circuit, allowing the developers to connect the board a PC’s USB port for downloading and debugging. Featuring ...

SKU: SF-SEN-14709

The AH1815 is an integrated Hall-Effect non-latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A...

SKU: SF-COM-30157 · MPN: COM-30157

The ATMEGA2560-16AUR is a high-performance, low-power 8-bit microcontroller based on the Microchip AVR enhanced RISC architecture. It is the controller IC used at the heart of the Arduino Mega and many other advanced controller boards, making it a strong choice for complex embedded projects that ...

SKU: DF-DFR0605

Gravity: Digital RGB LED Module is a cascadable single RGB LED module compatible with RGB LED strip. The Gravity interface provides a more elegant manner for the connections between modules and most of mainstream controllers such as Arduino, micro:bit, Firebeetle Series, LattePanda, and Raspberry...

SKU: SF-PRT-15773

A black anodised aluminium heatsink case for the Raspberry Pi 4 that provides 10–15°C of passive cooling under full CPU load. The entire case acts as a heatsink, delivering completely silent cooling — ideal for home media centres and other noise-sensitive applications. Comes with a thermal pad f...

SKU: DF-TEL0190 · MPN: TEL0190

RainbowLink V2 is a pocket-sized USB Type-C serial debugging workstation that combines four independent communication channels with useful field power outputs. It replaces multiple USB dongles for RS485, RS232 and TTL UART work, making it well suited to field engineering, IoT development and indu...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: DF-KIT0069

The DFRobot Bluetooth 4.0 RGB LED Strip Kit combines a 3-metre WS2812 addressable LED strip with a Bluno (Arduino-compatible Bluetooth 4.0 board), sound sensor, and audio analyser. Control every individual LED from your iPhone or Android device via Bluetooth Low Energy — change colours in real ti...

SKU: TB-ZR1020

The 1N5819 is a popular Schottky barrier rectifier diode featuring low forward voltage drop and fast switching. Its 40V reverse voltage rating and 1A current capacity make it ideal for power supply circuits, flyback protection, and solar panel applications. Schottky diodes have a lower forward v...