All Products

SKU: AF-1451

Diffused 5mm tri-colour LEDs with separate red, green, and blue chips inside a square "Piranha" (super-flux) package. With a 90° viewing angle and up to 3000mcd combined brightness, these LEDs are great for colour mixing, indicators, and illumination projects. They plug into a breadboard diagonal...

SKU: SF-COM-10821

A 5 mm diffused RGB LED with a common anode configuration. Three individual colour channels (red, green, blue) share a single anode pin, allowing independent control of each colour. Use it as a multi-colour status indicator, or drive all three channels with PWM to mix custom colours. The diffuse...

SKU: AF-848

Make some beautiful colors with these diffused 10mm tri-color LED with separate red, green and blue LED chips inside! They make a nice indicator, and fun to color-swirl. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs. These are Common-Anode type w...

SKU: AF-159

Diffused 5mm tri-color LED with separate red, green and blue LED chips inside! Nice indicator, and fun to color-swirl. 60 degree viewing angle. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs. These are Common-Anode type which means you connect one...

SKU: AF-302

Diffused 5mm tri-color LEDs with separate red, green and blue LED chips inside! Nice indicator, and fun to color-swirl. 60 degree viewing angle. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs. These are Common-Anode type which means you connect on...

SKU: AF-6156 · MPN: ADA6156

This diffused RGB backlight is a rigid acrylic light panel like the kind normally found behind LCD displays, but with a full-colour LED instead of a plain white backlight. The acrylic spreads the light from a single LED to give a near-uniform glow across the lit area.The flat rear side includes a...

SKU: DF-FIT1033 · MPN: FIT1033

This thin, flexible RGB light-emitting panel is designed for embedded systems, custom LCD backlights and diffuse indicator lighting. It uses separate red, green and blue channels to produce RGB colour output, with a common anode interface for driving from your own electronics.The bendable panel c...

SKU: AF-315

These clear 5 mm Piranha (super-flux) LEDs contain separate red, green, and blue chips in a single square package, allowing full RGB colour mixing. With an 80° viewing angle and a combined brightness of up to 2000 mcd, they work well as indicators, illuminators, or colour-swirl effects. The squar...

SKU: AF-2524

This high-power RGB LED from Adafruit delivers serious brightness, with each red, green, and blue die capable of handling 350–750mA continuous current (2A peak). At 3W it produces approximately 150 lumens, scaling up to around 300 lumens at the full 9W. The LED comes pre-mounted on an aluminium ...

SKU: AF-6158 · MPN: ADA6158

This diffused acrylic backlight strip gives you an easy way to add a smooth, colourful glow to projects. It is the kind of light guide normally found behind LCD panels, but this version uses a single RGB LED so you can drive red, green and blue channels independently.The LED is encased in a 3.3mm...

SKU: LB-ETEXTILERGB

A sewable tri-colour RGB LED module designed for e-textiles and wearable electronics. By grounding the red, green, or blue channel pins individually or in combination, you can produce any colour. The common-anode design means each channel turns on when its pin is connected to ground. The module ...

SKU: AF-4660

A rugged, chrome-plated latching pushbutton with a built-in RGB LED ring. Drill a 16 mm hole in any panel up to 6.35 mm (1/4") thick and mount it securely — an included rubber gasket provides a water-resistant seal for enclosures. The flat metal actuator latches on press and releases on a second...

SKU: AF-2739

Make some beautiful colors with these diffused rectangular 2.5mm x 5mm RGB LEDs with separate red, green and blue LED chips inside! They make nice indicators, and they're fun to color-swirl! We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct ...

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: SF-DEV-08467

Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can create any color. Very bright output. This is a common anode design - to turn on a channel you simply need to ground one of the R/G/B pins to illuminate that chann...

SKU: AF-679

These are very interesting 5mm diffused RGB LEDs - instead of having 4 pins to control 3 LEDs, they have only two leads - power and ground. When powered, the LEDs perform a slow fade through the rainbow, from red to orange to yellow, etc till they get back to red. See the video below for th...

SKU: AF-1378

The WS2811 is the driver IC used in NeoPixel LED strips and pixels. In this SOIC-8 package, it lets you build your own addressable RGB LEDs by driving a single common-anode RGB LED or three individual single-colour LEDs. Each output provides ~18 mA constant current, ensuring consistent colour reg...

SKU: DF-FIT0372

Have you ever played with LEDs and got hurt in your eyes? This pack of diffused LEDs won't. !Diffused LEDs are really useful in indications, they look softer and more uniformed so that you can see them well from any angle.This pack includes 50 5mm LEDs in 5 different colors: green, red, yellow, ...

SKU: AF-5888 · MPN: ADA5888

This handy STEMMA board lets you control 'true analog' LED strips and other PWM-able LEDs from a NeoPixel-compatible data line, without the usual extra wiring of separate driver FETs. A WS2811F handles the 800KHz NeoPixel signal and drives AO3406 N-channel FETs, so a common-anode RGB strip or LED...

SKU: SF-COM-07844

This is the very popular RGB combo but in SMD form. These units have four pads with a common anode configuration. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors! Simple breakout board available below. Iv (Typical): Red: 81mcd Green: 130mcd B...