All Products

SKU: DF-SEN0451 · MPN: SEN0451

This industrial Gravity kit measures electrical conductivity in aqueous solutions, helping you evaluate water quality by tracking dissolved content or salinity. It is suited to hydroponics, aquaculture and environmental water monitoring where long-running measurements are needed.The pro probe is ...

SKU: DF-SEN0169-V2

DFRobot Gravity: Analog pH meter pro V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in various applications such as aquaponics, aquaculture, and environmental water testing.As an upgraded version of pH meter pro V1, the sec...

SKU: DF-KIT0131 · MPN: KIT0131

Build a DIY water quality monitor for field studies, teaching or environmental projects with the KnowFlow Basic Kit. This Arduino-based kit measures two key water parameters: pH and electrical conductivity (EC).Data can be recorded automatically to a micro-SD card for later analysis, and the Blun...

SKU: DF-SEN0237-A

Measure dissolved oxygen in water for aquaculture, environmental monitoring, natural science projects and general water-quality work. This DFRobot Gravity kit pairs a galvanic dissolved oxygen probe with an analogue signal converter board for easy use with Arduino and other microcontrollers that ...

SKU: DF-DFR0300

The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring water quality, nutrient levels in hydroponic systems, and soil salinity in agricultu...

SKU: DF-SEN0189

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...

SKU: DF-SEN0161

You may check the latest version - Gravity: Analog pH Sensor/Meter Kit V2 to meet your requirements and Liquid Sensor Selection Guide to get better familiar with our liquid sensor series.Need to measure water quality and other parameters but haven't got any low-cost pH meter? Find it difficult t...

SKU: DF-DFR0504

The Analog Signal Isolator can isolate analog signal and provide isolated power to sensors. It can effectively prevent sensor signal interference and apply to multi-parameter water quality monitoring sensors. Because usually sensors will be interfered by the other sensors during the measurement,...

SKU: DF-DFR0565

Gravity: Digital Signal Isolator is capable of isolating I2C digital signal and providing isolated power to the sensor module, effectively preventing mutual interference between the sensor modules. This digital signal isolator can be used for multi-parameter water quality detection systems to pre...

SKU: DF-DFR0300-H

Gravity: Analog Electrical Conductivity Sensor / Meter(K=10) OverviewDFRobot Gravity: analog electrical conductivity sensor/meter(K=10) is particularly used to measure the high electrical conductivity liquid, such as seawater, concentrated brine, etc. The measurement range is up to 100ms/cm. This...

SKU: DF-SEN0165

In the ever-increasing need and awareness for health and safety, water has become a focus point for proper disinfection treatment as aftereffects of industrialization can become a danger for contamination of water via direct contact. Water is a critical control point of contact where proper t...

SKU: DF-SEN0244

The Gravity Analog TDS Sensor is an Arduino-compatible kit for measuring Total Dissolved Solids (TDS) in water. TDS indicates how many milligrams of soluble solids are dissolved per litre — the higher the value, the less clean the water. This sensor outputs a 0–2.3V analog signal that can be read...

SKU: DF-SEN0659 · MPN: SEN0659

This industrial CO2 probe is built for reliable carbon dioxide monitoring in environments such as indoor air quality systems, pipelines, greenhouses and fresh air systems. It uses NDIR sensing to measure CO2 from 400 to 5000 PPM and supports manual calibration for dependable readings.The IP65-rat...

SKU: DF-SEN0220

The Gravity UART Infrared CO2 Sensor uses non-dispersive infrared (NDIR) technology to measure carbon dioxide concentrations from 0 to 50,000 ppm. It offers excellent selectivity with no oxygen dependency, built-in temperature compensation, and a service life of over 5 years. The UART interface m...

SKU: DF-SEN0566

Fermion: MEMS Volatile Organic Compounds VOC Gas Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. ...

SKU: DF-SEN0565

Fermion: MEMS Methane CH4 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. The sens...

SKU: DF-SEN0574

Fermion: MEMS Nitrogen Dioxide NO2 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery....

SKU: DF-SEN0161-V2

The Gravity Analog pH Sensor/Meter Kit V2 is designed to measure the pH of liquids, indicating acidity or alkalinity on a scale of 0–14. It's commonly used in aquaponics, aquaculture, hydroponics, and environmental water testing. The kit includes a laboratory-grade pH probe, a signal conversion b...

SKU: DF-SEN0464

As an upgraded version of Industrial Gravity: ORP Sensor Meter For Arduino, this new generation ORP probe employs platinum indicator electrode and silver-silver chloridereference electrode, which makes it available for 24-hour online ORP monitoring and greatlyenhances product durability. The new ...

SKU: DF-DFR1184 · MPN: DFR1184

The Gravity 0–10V ADC Module is a high-precision dual-channel analogue-to-digital converter designed to interface industrial-grade 0–10V sensors with microcontrollers and Linux-based systems. Built on the Texas Instruments ADS1115, it delivers 15-bit resolution (0.375 mV per step) with ±2 mV accu...