All Products

SKU: EC-MCS02930M

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive the servo with arduino pin9 and pin10. Features Be able to drive 4 DC motor and...

SKU: AF-324

A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA so that it could be driven easily with an Adafruit motor shield for Arduino (or other motor driv...

SKU: DF-FIT0577

This DC gearmotor are now in the status of Pre-order and will ship in the end of Jun. This DC gearmotor has an integrated M3*20mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 98RPM, equivalent to 1.1mm/s. The brass facepla...

SKU: DF-FIT0016

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts.  It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for ...

SKU: SF-ROB-09238

This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a Bipolar Motor. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 12V Rated Current : 0.33A Holding Torque : 2.3kg*cm 5mm Diameter Drive Shaft Winding resistance: 32.6 Ω Winding inductance: 48 ...

SKU: DF-FIT0419

INTRODUCTION This is a new micro DC geared motor, using planetary gear mechanism, applicable to the various types of DIY project. Especially the project which has a certain requirements for size. It will be a good partner for you. SPECIFICATION ...

SKU: AF-2424

This stepper motor is a little different than the large NEMA-17 types you may be used to. These are often used in gauges for motorcycles and cars to replace the old-style fully-analog type. They have extremely fine step precision of about 1/2 a degree per step, 600 steps for single stepping, f...

SKU: PL-1120

A 200:1 plastic gearmotor with a 90-degree output shaft, offering a compact and affordable solution for small robot designs. The low-current brushed DC motor is well-suited for use with common motor drivers, and the recommended operating voltage range is 3–12V. The gearbox is fully enclosed and ...

SKU: PL-1125

A compact, inexpensive brushed DC motor with a 120:1 plastic reduction gearbox, well suited for small robot builds. The motor is rated for 4.5V but runs comfortably in the 3–6V range. The gearbox output shaft is a 3mm D-shape, offset from and parallel to the motor shaft. A built-in safety clutch ...

SKU: PH-103393

A Raspberry Pi motor controller HAT built around the L293D dual H-bridge driver IC, designed to make building a Raspberry Pi robot easy and fun. Control up to 4 DC motors or 2 stepper motors at up to 600 mA (1 A peak) per channel. The board includes breakout connectors for IR line sensors and an...

SKU: DF-FIT0441

INTRODUCTION   This is a motor revolution: a new DC brushless motor with built-in motor driver. It can be conncected to Arduino directly without external motor driver. Whatsmore, the motor comes with directional control, PWM speed control and speed feedback output, which make this motor t...

SKU: SF-ROB-09347

Here, for all your mechatronic needs, is a simple, high quality continuous continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-pin power and control cable is attached and all hardware listed below is included...