All Products

SKU: AF-512

A PSP/Xbox-style analog thumb joystick with a built-in press-to-select button, mounted on a breakout board designed for easy panel mounting. Unlike simple directional joysticks, this analog stick provides precise, proportional X and Y readings for accurate positional control. The breakout board ...

SKU: AF-424

A six-piece precision screwdriver set covering the most common sizes found in consumer electronics, small devices, and maker projects. The set includes three Phillips and three flat-head drivers in a compact carrying case. Each screwdriver features a contoured plastic handle with textured grip s...

SKU: AF-2765

The Mini 2-Axis Analog Thumbstick is a compact, self-centring joystick with a black rocker cap, similar in style to PSP joysticks. It provides smooth directional analogue input using two 10 kΩ potentiometers — one for the X-axis and one for the Y-axis. The voltage output follows the motion of th...

SKU: AF-3217

Does your prototyping project require soldering? Are you looking for something other than your usual run-o'-the-mill solder wire? Look no further! This high quality, low cost, adorably packaged Lead-Free Prototyping Solder Paste from IC Breakout will provide strong, flux-aided conductive bon...

SKU: SF-COM-11274

It’s the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a pre-installed long life horizontal microswitch. Button can also be adjusted to a low profile button by removing the midd...

SKU: SF-COM-11273

This large 100 mm yellow dome pushbutton is hard to miss and satisfying to press. It features a built-in LED indicator, a pre-installed long-life microswitch, and a polycarbonate lens cap for optical clarity. The height can be adjusted to a low-profile configuration by removing the middle ring. ...

SKU: SF-COM-11275

It’s the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a pre-installed long life horizontal microswitch. Button can also be adjusted to a low profile button by removing the midd...

SKU: TB-HK7715

These knobs just push on to a standard 0.25 (1/4) shaft. - No more messy screws. - Complete with coloured cap. Specifications Colour / Finish Black Shaft Type 1/4" Flattened Side...

SKU: TB-HK7711

These knobs just push on to a standard 0.25 (1/4) shaft. - No more messy screws. - Complete with coloured cap. Specifications Colour / Finish Black Shaft Type 1/4" Flattened Side...

SKU: DF-SEN0169

This is a professional Arduino pH Sensor Meter Kit with industrial electrode. It has built-in simple, convenient , practical connection and long life (up to 1 year), which makes it very suitable for long term online monitoring. It has an LED which works as the Power Indicator, a BNC connector...

SKU: DF-DFR0029-G

The DFRobot Gravity Digital Push Button (Green) is a simple momentary switch with an on-board LED indicator, designed for the Gravity interface system. It features an immersion gold PCB surface, a bright green cap, and a standard 3-pin digital connector for plug-and-play use with Arduino and othe...

SKU: DF-DFR0029-B

The Gravity Digital Push Button (Blue) is a simple momentary push button module designed for the DFRobot Gravity interface. It features an onboard LED indicator, immersion gold PCB surface, and a coloured button cap. A "D" marking on the board identifies it as a digital sensor for quick wiring re...

SKU: DF-DFR0008

The upgraded Arduino Input Shield includes a two axis mini joystick (with moment switch) as well as four colored push buttons(Red,Yellow,Blue,Green). The reserved APC220 Radio Data Module(SKU:TEL0005) interface and the Xbee interface is deisgned to facilitate the realization of wireless ro...

SKU: DF-SEN0161

You may check the latest version - Gravity: Analog pH Sensor/Meter Kit V2 to meet your requirements and Liquid Sensor Selection Guide to get better familiar with our liquid sensor series.Need to measure water quality and other parameters but haven't got any low-cost pH meter? Find it difficult t...

SKU: DF-DFR0225

RoMeo V2 [R3] is an All-in-One Arduino based robot board, it is especially designed for robotics applications, and extended devices. Romeo benefits from the Arduino open source platform, it is supported by thousands of open source projects, and can easily be expanded with Arduino Shields. The ...

SKU: DF-FIT0224

This mounting kit provides you different types of screws and nuts which are most commonly used in our projects here at DFRobot. We use them to mount circuit boards and help build robots. These screws and nuts are put into different compartments of an adjustable compartment parts box(Adjus...

SKU: SF-COM-09179

A 33 mm round momentary pushbutton in arcade style with a convex green cap. Features a simple screw-in design for easy panel mounting — ideal for arcade builds, interactive projects, and control panels. Specifications Button Type – Momentary, convex Colour – Green Diameter – 35.75 mm Height...

SKU: SF-COM-09181

It’s the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a pre-installed long life horizontal microswitch. Button can also be adjusted to a low profile button by removing the midd...

SKU: SF-TOL-09200

It’s like an Xacto knife, only better. We use these extensively when working with PCBs. These small knives work well for cutting traces, scraping ground pours, and guiding hair-like wires into their proper place. Excel knife comes with aluminum handle, one ultra-sharp blade, and safety cap.

SKU: SF-COM-09337

This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button has a great tactile, ‘clicky’ feel.Features: Concave plunger design Durable nylon material Microswitch: max 3A @ 120 VAC Microswitch reliability test...