All Products

SKU: LB-LR0228

These are the popular 28YBJ-48 geared stepper motors with driver board. The motor and driver are suitable for 5V operation. 4 Phase Current : 160 mA per winding (320 mA in 4-step mode) Measured: 250mA stopped, 200 mA running fast Resistance : 31 Ω per coil winding (from Red wire to any coil) ...

SKU: LB-LR0180

Including CNC Shield V3.0The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors. Each channel of stepper motor only needs 2 I...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: LB-OWL-HBRIDGE

Using the powerful L298N Dual Motor Driver，this module allows full control of two DC Motors or one stepper-motor. Screw Terminals for easy connections；LEDs show power and output status. Requires six digital inputs. Has 4 mounting holes. Specification: Chip: L298N  Maximum Output Curre...

SKU: DF-FIT0495-G

A compact metal DC geared motor with a 45:1 reduction gearbox, delivering up to 1.2 kg·cm of torque. The all-metal gears provide durability and stability for robotics and mechanical projects. Features a D-shaped 4 mm output shaft. Specifications Rated Voltage – 6V DC Operating Voltage – 2–7.5...

SKU: DF-FIT0016

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts.  It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for ...

SKU: SF-ROB-09238

This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a Bipolar Motor. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 12V Rated Current : 0.33A Holding Torque : 2.3kg*cm 5mm Diameter Drive Shaft Winding resistance: 32.6 Ω Winding inductance: 48 ...

SKU: SF-ROB-12779

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The E...

SKU: DF-DRI0023

INTRODUCTION Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain......? As we all know, regular stepper motors are hard to drive, but with this stepper motor shield, you can easily drive 2 stepper motors vi...

SKU: PH-103393

A Raspberry Pi motor controller HAT built around the L293D dual H-bridge driver IC, designed to make building a Raspberry Pi robot easy and fun. Control up to 4 DC motors or 2 stepper motors at up to 600 mA (1 A peak) per channel. The board includes breakout connectors for IR line sensors and an...

SKU: KI-5698

A compact motor driver board for the BBC micro:bit that drives two DC motors or one stepper motor. The integrated edge connector lets the micro:bit slot in directly, with built-in protection against short circuits, overcurrent, and overheating. Power is supplied via terminal block or servo conne...

SKU: DF-DRI0041

An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...

SKU: PL-2128

The Black Edition of the A4988 stepper motor driver carrier features a four-layer PCB for better thermal performance, allowing the A4988 to deliver approximately 20% more current than the standard two-layer (green) version. It is a drop-in replacement for the original carrier in most applications...

SKU: AF-324

A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA so that it could be driven easily with an Adafruit motor shield for Arduino (or other motor driv...

SKU: EC-CDP03051C

The Arduino CNC Shield V3.51 by Protoneer turns an Arduino Uno into a 4-axis CNC controller. Compatible with GRBL 0.9 firmware, it accepts Pololu-style stepper drivers (sold separately) and supports up to 4 stepper motors for CNC routers, laser cutters, 3D printers, and other precision motion pro...

SKU: LB-LR0259

This compact 9 g micro servo is an affordable, simple actuator for small mechatronics projects, robot linkages and model mechanisms. It can operate from 3.0 V to 7.2 V, with the supplied feature ratings listed at 6.0 V where noted.A 3-wire cable provides ground, power and control, terminated in a...

SKU: PL-611

Need more power out of your gear motor? This is a high-power brushed DC motor that fits in the same form factor as used by the GM2/3/8/9 style gear motors.

SKU: AF-2442

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. Good for making simple moving robots. Comes with five horns and attachment screw...

SKU: AF-3190

The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...

SKU: AF-4225

Everything you need (besides the Jetson Nano) to build NVIDIA's JetBot — an open-source AI robot platform. This parts pack includes the motor driver, motors, wheels, and a handy PiOLED display to get your JetBot rolling. The included DC Motor + Stepper FeatherWing provides I2C control for two br...