All Products

SKU: SF-BOB-10680

A breakout board for the SOIC version of the 74HC595 8-bit shift register IC. Shift registers let you expand the number of digital outputs available on your microcontroller by clocking in serial data and latching it to eight parallel outputs — using just three GPIO pins. All IC pins are broken o...

SKU: SF-DEV-17047

The SparkFun Qwiic GPIO adds eight additional digital I/O pins to your project via I2C, based on the TCA9534 I/O Expander from Texas Instruments. Read and write pins just like standard Arduino digital pins using the included library — functions mirror familiar pinMode and digitalWrite calls. All...

SKU: SF-SEN-14520

The SparkFun Capacitive Touch Breakout provides a single momentary touch button using the AT42QT1011 capacitive sense chip. Simply supply 1.8–5 V and ground — the chip handles all touch monitoring and outputs a digital high signal when a touch is detected, low when released. Unlike the AT42QT101...

SKU: SF-PRT-14313

This Digital LED Voltmeter measures the voltage at a particular point of the system it has been hooked up to and then provides a readout on its three 7-segment LEDs. This voltmeter is able to provide a readout of voltages from 2.5VDC to 30VDC within a 1% accuracy. Features: Range: 2.5VDC — 30V...

SKU: SF-KIT-19518

The SparkFun PIR Breakout Starter Kit includes everything needed to get started with passive infrared motion detection. Built around the Panasonic EKMB1107112 PIR sensor, this kit's breakout board offers ultra-low 1µA standby current, making it ideal for battery-powered motion-sensing application...

SKU: SF-SEN-14349

This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view, so not only can the AK9753 detect a human, but it can also tell which directio...

SKU: SF-SEN-14722

This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the ref...

SKU: SF-SEN-12064

The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for a weather stations or humidor control systems. All you need is two lines for I2C communication and you’ll have relative ...

SKU: SF-DEV-15423

Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an A...

SKU: SF-SEN-11446

A breakout board for the Analog Devices ADXL362, a 3-axis MEMS accelerometer that operates at ultra-low power consumption. It measures both dynamic acceleration (motion, shock) and static acceleration (tilt), and communicates over SPI. Built-in digital logic enables autonomous "wake-on-shake" ope...

SKU: SF-COM-10613

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mechanical knob required. Because the wiper is software-controlled, you're not lock...

SKU: SF-DEV-15162

The SparkFun gator:bit v2.0 is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips connect to so you can get the ...

SKU: SF-WRL-16781

The SparkFun MicroMod ESP32 Processor Board brings Espressif's ESP32 into the MicroMod ecosystem via the M.2 connector interface. It provides WiFi and Bluetooth connectivity with the processing power of a dual-core Tensilica LX6 at 240 MHz. Simply align the keyed edge connector with any MicroMod...

SKU: SF-KIT-19519

The SparkFun 170uA PIR Breakout Starter Kit comes with everything you need to get started using Passive Infrared (PIR) sensors. PIR sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series ...

SKU: SF-KIT-16274

The SparkFun micro:climate kit is a full weather station kit that is built on top of the weather:bit carrier board. Unlike previous weather kits we've carried, this micro:climate kit is Qwiic enabled and includes our tried-and-true Weather Meters and Soil Moisture Sensor, so whether you’re an ...

SKU: SF-DEV-21247

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, digital cameras, Bluetooth dongles, game controllers, and more. This version up...

SKU: SF-BOB-15439

The SparkFun PCA9306 Level Translator Breakout provides dual bidirectional voltage-level translation for I2C and SMBus lines. It lets you safely connect devices operating at different logic levels — for example, a 3.3V sensor to a 5V microcontroller — without a direction pin. Simply apply your re...

SKU: SF-SEN-28867 · MPN: SEN-28867

This rain gauge measures rainfall using a self-emptying bucket-type mechanism. Each time enough rain is collected, it triggers a momentary button closure that can be read by your electronics project.The switch closure can be measured with interrupt pins or a digital counter, making it suitable fo...

SKU: SF-DEV-14779

The LumiDrive LED Driver is SparkFun’s foray into all things Python on micro-controllers. With the SparkFun LumiDrive you will be able to control and personalize a whole strand of APA102s directly from the board itself. We’ve broken out a number of analog and digital pins from the on board SAMD21...

SKU: SF-SEN-16476

The SparkFun Qwiic MicroPressure Sensor is a miniature breakout equipped with Honeywell's MPR Series piezoresistive silicon pressure sensor. This MicroPressure Sensor offers a wide pressure sensing range of 60mbar to 2.5bar, easy to read 24 bit digital I2C output, and can be calibrated and compen...