All Products

SKU: AF-5990 · MPN: ADA5990

The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-channel FET at 100–200 mA per LED, you get 10+ metres of transmit range alongside ...

SKU: AF-1131

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...

SKU: AF-5940 · MPN: ADA5940

This breakout uses Vishay's TSSP77038 infrared demodulator to give you the raw demodulated output from a 38kHz IR signal, without the extra filtering used in typical remote-control receivers. That makes it a handy choice for reflective sensing, light barriers, fast proximity detection, and modula...

SKU: AF-5580

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: AF-4712

The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...

SKU: AF-6051 · MPN: ADA6051

Add magnetic sensing to your project with this breakout built around the Texas Instruments DRV5032 digital Hall effect sensor. Its digital output changes when the magnetic flux density threshold is crossed, making it useful for detecting magnets, position, lids, doors, rotations and other simple ...

SKU: DF-FIT0914 · MPN: FIT0914

A 10-pack of PH2.0-4P male-to-male cables for connecting Boson modules, UNIHIKER boards, and other modular electronics. The polarised 4-pin connectors ensure correct orientation and prevent reverse insertion. Key Features Polarised Connectors – Prevents incorrect insertion 4-Pin PH2.0 – Male ...

SKU: EF-EF10116

This is a long flexible purple cable. It is called EL wire or electroluminescent wire. Once being charged with appropriate voltage, it can emit bright purple light and the wire will not be heated. It is similar to a long thin tube full of fluorecent liquid. In the one end, it is terminated with a...

SKU: AF-261

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in t...

SKU: AF-3955

This 200 mm cable converts a JST PH 4-pin connector into four individual wires with 0.1″ (2.54 mm) male header pins on the end. It's designed for connecting STEMMA and Grove I²C boards to breadboards, socket headers, or any standard 0.1″ pitch connection. Key Features JST PH to Male Headers – ...

SKU: AF-783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: AF-5791

The Adafruit STEMMA Piezo Driver Amp uses the PAM8904 switched-capacitor driver to amplify signals for piezo elements at up to 300 kHz. With bridge-tied load (BTL) output and up to 3× voltage multiplication, it can deliver approximately 13 Vpp — much louder than driving a piezo directly from a 3V...

SKU: DF-DFR1230 · MPN: DFR1230

This Gravity DAC module converts I2C or PWM digital signals into stable analogue voltage or current outputs for control and automation projects. Built around the GP8630N chip, it supports output modes such as ±10V, 0-5V, 0-10V and 4-20mA, with 16-bit resolution available in I2C mode.The symmetric...

SKU: AF-3814

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can ...

SKU: SF-TOL-27923 · MPN: TOL-27923

This handy tool helps remove a standard 2-pin JST-PH connector with 2mm pitch, such as the female connector commonly found on single-cell LiPo batteries. It gives you something safer and easier to grip than the connector body itself, helping avoid sore fingertips, pinched wires from needle nose p...

SKU: AF-4424

A 200mm adapter cable with a JST-SH 4-pin connector (STEMMA QT / Qwiic, 1mm pitch) on one end and a JST-PH 4-pin connector (STEMMA / Grove, 2mm pitch) on the other. Use it to bridge I2C sensors and drivers between the two connector ecosystems. Both connectors have a latching feel for secure conn...

SKU: PI-COM0808

A miniature brushed DC motor with a 20:1 metal gearbox and an extended back shaft for mounting optical encoders. All micro metal gearmotors share the same physical dimensions, so different gear ratios can be easily swapped without changing your mechanical design. Key Features 20:1 Metal Gearbo...

SKU: SF-PRT-09750

A 3-pin right-angle JST PH series through-hole connector with 2mm pin spacing. These compact connectors provide a solid locking connection and are rated for moderate current, making them a reliable choice for PCB-mounted sensor and peripheral connections. Commonly used to interface with Sharp in...

SKU: AF-5090

A matching pair of 6-pin JST PH compatible cables with inline plug and socket connectors. Each cable is 20 cm long with stranded 26 AWG wires, providing a reliable and compact connection that can carry a couple of amps of current. The friction-lock connectors make it easy to connect and disconne...