All Products

SKU: LB-LR0293-5

This HDMI-to-VGA adapter cable converts a digital HDMI signal to analogue VGA output, letting you connect HDMI devices like a Raspberry Pi, laptop, or media player to a VGA monitor, projector, or LCD screen. It features a built-in conversion chipset and requires no external power — it draws power...

SKU: AF-5650

The Feather RP2040 SCORPIO is designed specifically for driving large quantities of NeoPixels (WS2812) using the RP2040's PIO state machines. It features 8 consecutive GPIO outputs with a 3V-to-5V level shifter, allowing you to drive 8 independent NeoPixel strips simultaneously via DMA — with zer...

SKU: AF-2353 · MPN: 2353

This 7.0" TFT display packs 800×480 pixels with an LED backlight and 24-bit colour capability via its 40-pin connector (8 red, 8 green, 8 blue parallel pins). It's ideal for projects requiring a large display area for graphics, menus, or data visualisation. This is a raw pixel-dot-clock display ...

SKU: AF-5980 · MPN: ADA5980

The Feather RP2040 Adalogger combines the RP2040 dual-core processor with a MicroSD card holder for data logging and file storage. It features 8 MB SPI flash, 264 KB SRAM, USB Type C, STEMMA QT connector, and built-in LiPo battery charging — ready for portable data recording projects with Arduino...

SKU: WS-13857

A 7-inch IPS HDMI display with case from Waveshare, featuring 1024×600 hardware resolution (configurable up to 1920×1080 via software). The toughened glass capacitive touch panel (6H hardness) provides smooth 5-point touch input on supported systems. Compatible with Raspberry Pi, Jetson Nano, Be...

SKU: AF-5723

The Feather RP2040 with USB Type A Host adds a full USB Type A port to the Feather, letting you connect USB devices like keyboards, mice, flash drives, and serial peripherals. The USB host functionality is achieved through the RP2040's PIO peripheral, which emulates a USB host controller while ke...

SKU: SF-DEV-20594

The SparkFun DataLogger IoT - 9DoF is a preprogrammed data logger that automatically detects, configures, and logs Qwiic-compatible sensors — all without writing a single line of code. Simply plug in your sensors, power up, and start capturing data to a microSD card or send it wirelessly to your ...

SKU: SF-GPS-22693 · MPN: GPS-22693

This high-precision GNSS breakout is built around the u-blox ZED-F9R, combining RTK positioning with Automotive Dead Reckoning (ADR) sensor fusion. It fuses a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data and GNSS measurements to provide accurate and continuous positioning...

SKU: AF-3560 · MPN: 3560

A 10cm (~4″) flexible HDMI ribbon cable for building custom HDMI connections with DIY HDMI adapters. Simply clip any two compatible HDMI plug adapters onto each end of the ribbon cable to create the exact cable configuration you need. Tested at 1080p with Raspberry Pi. Note that DIY ribbon cable...

SKU: AF-978 · MPN: 978

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above and ...

SKU: AF-3549 · MPN: 3549

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty!...

SKU: SS-320990008

This is HDMI male connector without wire. It exposes all the HDMI wire as bare pins so that you can hack it easily.   Features: Bare connector Easy to hack   Specification: Current rating: 0.5A AC,DC Voltage rating: 40V AC,DC Temperature range: -40℃ to +85℃ Withstand vo...

SKU: SF-PRT-16890

These are the surface mount 50 pin 0.5mm Board to Board Double Slot Female Connectors found on the Alchitry FPGA boards. These headers allow for Alchitry FPGA Boards to stack on one another by being soldered to the topside of the board.These connectors are sold in single units. Four of these conn...

SKU: SF-DEV-17724

The MicroMod Qwiic Carrier Board can be used to rapidly prototype with other Qwiic devices. The MicroMod M.2 socket provides users the freedom to experiment with any processor board in the MicroMod ecosystem. This board also features two Qwiic connectors and eight 4-40 screw inserts to connect an...

SKU: AF-73 · MPN: 73

The TV-B-Gone is a soldering kit that, once assembled, can turn off virtually any television within a 45 m (150 ft) range. It cycles through 230 power codes — 115 for American/Asian TVs and 115 for European models — so it works with everything from vintage CRTs to the latest flat-screen and plasm...

SKU: DF-DFR1015

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required.This DC-DC step-down voltage power module converts 7.5V~30V input to an output of 3.3V/5V/9V/12V (default to 5V), which can be selected by short-circuiting the correspondi...

SKU: SF-DEV-28369 · MPN: DEV-28369

This lockable Teensy 4.1 is aimed at advanced developers moving from prototype to a secure production design. It keeps the high-performance 600 MHz ARM Cortex-M7 platform of the Teensy 4.1 while adding write access to the chip’s eFuses so your final application can be encrypted and locked to the ...

SKU: EF-EF08199

ParameterSKU: EF08199/EF08200    The board: micro:bit    Coding language: makecode\python\C++    Power supply: 2 x AA    Connection line: banana line    Size: 25X17.6X3.8CM    Net weight: 885.5g    Documentsexperiment box kit

SKU: SF-GPS-17722 · MPN: GPS-17722

Built around the u-blox ZED-F9P, this MicroMod carrier gives your project high-precision GNSS and RTK positioning in a swappable, solderless MicroMod format. It supports rover and base station operation, with RTK accuracy down to millimetre-level positioning when used with suitable correction dat...

SKU: SF-COM-18732 · MPN: COM-18732

When your system needs a stable 12V rail from a variable DC supply, this industrial-grade buck-boost converter is built to deliver. It accepts a wide 8 to 36VDC input range and regulates it to 12V for loads up to 6A, or 72W.The buck-boost design automatically switches between stepping voltage dow...