All Products

SKU: DF-DFR0789

This is a simple LED-illuminated self-lock switch button. It’s just like a basic switch button, but it lights up color(red/yellow/green/blue/white) when pressed down, which gives you visual feedback. These little buttons can be used with micro:bit to realize various fun interactive projects, such...

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: LB-LS0014

Check out these big 10mm through-hole LEDs! The clear epoxy package causes these LEDs to have a bright glow. Features: Forward Voltage (R/G/B): 2.0 / 3.2 / 3.1V Forward Current: 20mA Intensity (R/G/B): 550 / 250 / 700 mcd Common Cathode This is a bag of 20 RGB LEDS

SKU: AF-5007

A 10-pack of translucent red DSA profile keycaps compatible with Cherry MX and MX-compatible switches. The translucent design allows RGB or LED backlighting to shine through for a vivid glow effect. DSA profile keycaps are fully symmetric in all four directions with a flat, uniform height across...

SKU: LB-RED-100

A bulk pack of 100 red 5mm through-hole LEDs. These standard LEDs are ideal for power indicators, status lights, and general-purpose projects. Key Features 5mm Diameter – Standard size for breadboards and PCBs Red Light – Classic indicator colour Through-Hole – Standard 2-pin design Bulk Pa...

SKU: AF-4203

A pack of 25 diffused 5mm LEDs in five colours — white, blue, green, yellow, and red (5 of each). These classic through-hole LEDs are bright enough for daytime visibility and diffused for a wide viewing angle, making them ideal for indicator lights, breadboard projects, and prototyping. Key Feat...

SKU: SF-DEV-14013

A pack of five red LilyPad LEDs on a snap-apart strip. Each LED has large sew tabs for stitching into fabric with conductive thread, making them ideal for wearable electronics and e-textile projects. The ultra-thin 0.8 mm PCB lies flat against fabric. Key Features 5× Red LEDs – Snap-apart stri...

SKU: AF-631

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Red Portable 4xAAA inverter powerful enough to drive a full meter of st...

SKU: SF-COM-16347

The WS2812B (or "NeoPixel") may look like a common 5050-sized (5x5mm) SMD LED, but there’s actually an integrated control circuit embedded inside there too. Sometimes you don't need 10 or even 50, maybe you need a whole reel of 1000! If you are the person who needs that many than this is the perf...

SKU: DF-TOY0175-EN · MPN: TOY0175-EN

This hands-on STEM kit lets kids build a working RGB LED camping lantern while learning the basics of electronic circuits and the primary colours of light. By connecting the LED, rotary controls and battery pack with colour-matched wires, children can see how a simple circuit brings their project...

SKU: AF-6428 · MPN: ADA6428

These incredibly small surface-mount LEDs are an easy way to add a lot of very tiny (but bright!) colorful dots to your project. They are just mind-bogglingly small - 2mm square. As they are pretty darn tiny, they might be a bit difficult to hand solder. SMT techniques with solder paste and hot a...

SKU: SF-COM-10191

EL wire, or electroluminescent wire, is a flexible wire coated in phosphor. Apply the appropriate voltage and it lights up! It looks a lot like a thin flexible neon tube. They come in many bright colors (check below for other colors) and can be driven pretty easily with an inverter. Check belo...

SKU: SF-COM-14560

You don’t have to worry about adding a resistor to an LED if you get an LED with a built in resistor! This pack of 25 red 5mm LEDs will help alleviate any frustrations you’ve had with accidentally burning them out by having a resistor in the diode itself. Each LED has an operating voltage range o...

SKU: AF-5255

The Adafruit LED Glasses Starter Kit includes everything you need to build a complete pair of programmable LED glasses. Pair the 116-LED front panel with the Bluetooth-enabled nRF52840 driver board, snap them onto the included fashion frames, and you're ready to create dazzling wearable light dis...

SKU: LB-EAGLED-MOMENTARY

A pack of 10 low-profile momentary push buttons designed for e-textile and wearable electronics projects. Each button features large sewing holes and flat connection pads with no sharp edges, making them comfortable to wear and easy to sew onto fabric with conductive thread. The button closes th...

SKU: PI-COM0610

Standard 10 mm through-hole yellow LED, sold in a pack of 5. These diffused LEDs are suitable for prototyping on breadboards or permanent installation in finished projects — ideal for power indicators, status lights, or decorative arrays. Key Features Size – 10 mm diameter, through-hole mount ...

SKU: LB-EAGLED-BUZZ

EagLED is Little Bird Electronics' wearable development kit: an Arduino-compatible microcontroller board with LEDs, a light sensor, push button and buzzer built into a snippable PCB for e-textile projects.Built-in USB support lets you program and power the board from a computer. It works with the...

SKU: LB-EAGLED-LED-O

EagLED LEDs are purpose-built for e-textiles and wearable projects. This pack of 10 orange sewable LEDs come attached to each other on a snappable strip — simply break them apart as needed and sew them into clothing, accessories, or whatever you can dream up. Made in Australia, they're a cost-eff...

SKU: AF-299

A pack of 25 diffused red 5 mm LEDs, bright enough to be visible in daylight and viewable from any angle thanks to the diffused lens. These are great all-purpose indicator LEDs that fit easily into a breadboard. Specifications Colour: Red Wavelength: 660 nm Diameter: 5 mm Lens Type: Diffuse...

SKU: AF-2176

Keep your 5 mm LEDs securely mounted with these chromed metal LED holders featuring a narrow bevel finish. Slot the LED through the opening, insert the plastic retaining cap, and tighten the threaded washer for a clean, professional look on any panel or enclosure. Key Features Chromed Metal – ...