All Products

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: LB-LS0221

The CJMCU-226 INA226 is a powerful voltage, current, and power monitoring module designed for high precision in both high-side and low-side sensing applications. With its bi-directional current sensing capability and wide operating range, this module is perfect for a variety of applications, incl...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: AF-4489

Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard.Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 sole...

SKU: AF-6223 · MPN: ADA6223

The Adafruit DAC7578 Breakout provides eight independent 12-bit digital-to-analogue converters in a single package, all controllable over I2C. Set precise output voltages on up to eight channels simultaneously, making it ideal for multi-channel voltage control, LED dimming, or sensor calibration....

SKU: SF-BOB-15439

The SparkFun PCA9306 Level Translator Breakout provides dual bidirectional voltage-level translation for I2C and SMBus lines. It lets you safely connect devices operating at different logic levels — for example, a 3.3V sensor to a 5V microcontroller — without a direction pin. Simply apply your re...

SKU: AF-1875

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.Although one can use resistors to make a divider, for high speed tr...

SKU: AF-856

The MCP3008 is an 8-channel, 10-bit analogue-to-digital converter (ADC) with an SPI interface. It adds analogue input capability to microcontrollers and microcomputers that lack a built-in ADC — such as the Raspberry Pi — using just four SPI pins. Key Features 8 Analogue Channels – Read up to ...

SKU: DF-DFR0913

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 3.3V, making it easy to interface industrial sensors and PLC outputs with Arduino, Raspberry Pi, and other 3.3V microcontrollers. Each channel features photoelectric isolation for reliable signal separation...

SKU: DF-DFR1229 · MPN: DFR1229

This GP8600 module is a high-precision digital-to-analogue converter for connecting logic-level microcontrollers to industrial-style analogue control inputs. It accepts I2C or PWM signals and converts them for applications such as 0-5V, 0-10V and 4-20mA control.It is designed for automation and c...

SKU: DF-TEL0190 · MPN: TEL0190

RainbowLink V2 is a pocket-sized USB Type-C serial debugging workstation that combines four independent communication channels with useful field power outputs. It replaces multiple USB dongles for RS485, RS232 and TTL UART work, making it well suited to field engineering, IoT development and indu...

SKU: DF-DFR0914

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 5V, making it easy to interface industrial sensors and PLC outputs with Arduino and other 5V microcontrollers. Each channel features photoelectric isolation for reliable signal separation between high and l...

SKU: AF-1698

Connect your DisplayPort and Mini DisplayPort sources and devices with this bi-directional cable! This cable has a standard sized DisplayPort (DP) connector on one end and a Mini DisplayPort (MDP) connector on the other. The cable is bi-directional, which means that you can use a DP source with a...

SKU: DF-DFR0911

The 2-Channel Level Converter translates 12V signals down to 3.3V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 3.3V microcontrollers like Arduino. It supports common anode, common cathode, and differential signal inputs with PNP output (NPN to P...

SKU: AF-5626

Need to use multiple I2C devices that share the same address? The PCA9548 8-Channel STEMMA QT / Qwiic I2C Multiplexer lets you connect up to eight same-address I2C devices with completely solderless wiring. Nine JST SH connectors (1 input + 8 outputs in two rows of four) make it plug-and-play wit...

SKU: SF-WRL-28896 · MPN: WRL-28896

  The RockBLOCK 9704 by Ground Control is a breakout board for the new Iridium 9704 including a built-in patch antenna and a supercap charger to enable low power operation. If you need low data rate connectivity over the entire globe, Iridium is the answer. RockBLOCK 9704 leverages the I...

SKU: DF-DFR0912

The 2-Channel Level Converter translates 12V signals down to 5V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 5V microcontrollers like Arduino. It supports common anode, common cathode, and differential signal inputs with PNP output (NPN to PNP c...

SKU: AF-3957

The Adafruit CRICKIT HAT is a robotics and electronics driver board that plugs directly onto any Raspberry Pi with a 2×20 GPIO header. It adds motor drivers, servo outputs, capacitive touch inputs, a level-shifted NeoPixel driver, and a 3W I2S audio amplifier — all managed over I2C via the Adafru...

SKU: SF-PRT-28203 · MPN: PRT-28203

  The SparkFun Qwiic 5V Boost simplifies interfacing 5V I2C devices with the 3.3V Qwiic ecosystem. It takes the 3.3V I2C signals and power from its Qwiic connectors and boosts them to 5V, available on the PTH pins. This is perfect for powering peripherals like RGB LEDs or DC fans commonl...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...