All Products

SKU: AF-371

A 150mm (6″) IDC ribbon cable with 6-pin (2×3) socket connectors on both ends at 0.1″ × 0.1″ (2.54mm) spacing. Commonly used for AVR ISP programming connections and other 2×3 header interfaces. Key Features Socket-to-Socket – 2×3 IDC connectors on both ends Standard 0.1″ Pitch – Compatible wi...

SKU: AF-4986

A matching pair of 1.25 mm pitch cables with 6-pin connectors — one inline socket and one plug — that friction-lock together for a secure, reliable connection. Each cable is 10 cm long, making them well suited for tight enclosures and compact builds. Compatible with Molex PicoBlade connectors an...

SKU: AF-4876

A matching pair of 6-pin JST XH-compatible cables — one with an inline plug and one with an inline socket — for easy connect-and-disconnect wiring. The 2.5mm pitch connectors friction-lock together for a secure, reliable connection that's easy to separate when needed. Each cable is 20cm long wit...

SKU: AF-2105

This little 2x3 (6 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with our 6-pin IDC cable. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header p...

SKU: AF-4364

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit.This is a USB C to TTL seri...

SKU: AF-4331

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit.This is a USB C to TTL seri...

SKU: AF-70

Just about all electronics use TTL serial for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. This is a USB to TTL serial cable, with a FTDI FT232RL usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V ...

SKU: SF-PRT-10361

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on the other end with a mating socket. Dimensions: 8" length Documents: Datashe...

SKU: AF-370

A 6" (150mm) IDC ribbon cable with 10-pin 2×5 socket connectors on both ends at standard 2.54mm (0.1") pitch. Commonly used for AVR ISP programming, JTAG connections, and other 10-pin box header interfaces. Key Features 10-Pin (2×5) – Standard box header socket connectors on both ends 2.54mm ...

SKU: AF-5294

This 20-pin GPIO ribbon cable provides a clean, reliable connection between PCBs, development boards, and breakout headers. The soft, flexible 0.05″ ribbon cable with keyed IDC connectors on both ends ensures correct orientation every time. Pin 1 is marked with a pink stripe along the side of th...

SKU: AF-4170

A 16-pin (2×8) IDC ribbon cable with keyed connectors on both ends, 305mm (12") long. The 0.05" pitch ribbon cable connects to standard 2×8 0.1" × 0.1" IDC headers. Pin 1 is marked with a white stripe along the cable edge. Key Features 16 Pins (2×8) – Standard IDC ribbon cable layout 305mm (1...

SKU: SF-PRT-00132

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two boards are included so be sure to buy two RJ11 connectors to fully utilize them! ...

SKU: AF-4437

This one's going out to all the makers and designers who use DIN railing in their builds. This adapter plate is perfect for simplifying complex wiring. You connect a 2x20 IDC cable to this very PCB, which can be DIN rail-mounted. Then, all 40 pins are broken out into terminal blocks, so...

SKU: DF-DFR0116

This is a USB AVR programmer supported by offical Arduino IDE. Once the Arduino has lost its bootloader for some reasons, use this programmer to reburn the bootloader and save the dead Arduino. This programmer works really well for ATmega168 and ATmega328 and should work with all the AVR micros ...

SKU: SF-CAB-13028

This 40-pin (2×20) flat ribbon cable connects to the GPIO header on the Raspberry Pi, providing easy access to all GPIO, I2C, SPI, UART, and power pins. The 6-inch (15 cm) length keeps things tidy while giving you room to work with breadboards, breakout boards, and HATs. The cable uses standard ...

SKU: AF-2270

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins).  It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the c...

SKU: AF-4702

The Adafruit RGB Matrix FeatherWing Kit for nRF52840 lets you drive HUB75-type RGB LED matrices from nRF52840-based Feather boards. With built-in power regulation and a compact form factor, it's the easiest way to create colourful scrolling displays and LED wall projects using the Feather ecosyst...

SKU: SF-CAB-15455

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cable's 3mm panel mount holes, spaced 18mm apart.

SKU: AF-2101

The "poor woman's" Raspberry Pi cobbler! This combo of 2x13 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A and B.  It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard o...

SKU: SF-CAB-09556

This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable’s connector is composed of two rows of five 0.1" spaced pins; it’s also polarized, as is the mating connector on-board the Bus Pirate, so you can only connect the cable in one direction. The lea...