All Products

SKU: AF-3720 · MPN: 3720

Praise the sun! You will never have that awkward situation where your caliper battery dies just when you need to take a measurement. Sure, if you have the budget, we recommend these near-indestructable high-end Mitutoyo calipers. But these are very fine calipers as well. The jaws are plastic, so...

SKU: DF-DFR1117

Introducing the Beetle ESP32 C6 Mini Development Board - the perfect solution for your wireless smart wearable device needs. This compact Arduino board is based on the powerful ESP32-C6 chip and boasts a sleek design with dimensions as small as a coin (25*20.5mm). With its high-performance 160MHz...

SKU: DF-DFR0679

SPRESENSE is a low-power board computer for the IoT that is equipped with a GPS receiver and supports High-Resolution Audio codecs. The board allows for IoT versatility and can be developed for a vast range of uses, such as a drone utilizing the GPS and high-performance processor, a smart speaker...

SKU: M5-K027

Description Note: M5StickV does not support for microphone function, which will be added on upcoming Wifi version M5StickV+. M5Stack recently launched the new AIOT(AI+IOT) Camera powered by Kendryte K210 -an edge computing system-on-chip(SoC) with dual-core 64bit RISC-V CPU and state-of-art ne...

SKU: PL-3581 · MPN: 3581

The RoboClaws from Basicmicro (formerly Ion Motion Control) are a family of efficient, versatile, synchronous regenerative motor controllers. They can supply brushed DC motors with 7.5 A, 15 A, 30 A, 45 A, 60 A, or 120 A continuous (depending on the model) at voltages from 6 V to 34 V or 10.5 V t...

SKU: AF-772 · MPN: 772

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the Blue & White 16x2 LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another pin to control the backlight for a total of 7 pins. That's al...

SKU: AF-714 · MPN: 714

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a...

SKU: ET-2432906

The BitScope Micro (BS05U) is a compact, probe-sized mixed signal oscilloscope and test instrument. Despite its tiny form factor, it delivers full-featured oscilloscope, logic analyser, and waveform generator functionality — all powered over USB. Compatible with Windows, macOS, Linux, and Raspbe...

SKU: SF-DEV-18288

The SparkFun Pro Micro RP2040 is a low-cost, high performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the good 'ol Pro Micro footprint, the board also includes a WS2812B addressable LED, boot button, reset button, Qwiic connec...

SKU: SF-KIT-18577

The SparkFun Tinker Kit (STK) is a great way to get started with programming and hardware interaction with the Arduino programming language. This latest version of the STK adds in the Qwiic functionality. Each SparkFun Tinker Kit includes everything you need to complete 11 circuits that will t...

SKU: SF-DEV-18721

The SparkFun RP2040 mikroBUS Development Board is a low-cost, high performance platform with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or Feather PTH pin layout, the board also includes a microSD card slot, 16MB (128Mbit) fl...

SKU: RP-RP2040-500

The RP2040 is Raspberry Pi's dual-core Arm Cortex-M0+ microcontroller in a compact 7mm × 7mm QFN-56 package. Built on 40nm silicon, it delivers high performance for integer workloads with flexible I/O for connecting to almost any external device. Features six independent RAM banks and a fully co...

SKU: AF-1612 · MPN: 1612

The NeoPixel Mini PCBs are among the smallest addressable RGB LED breakouts available. Each tiny board measures just 8 × 10 mm and features two sets of three solder pads on the back for easy wiring. The pixels are chainable — you only need one digital pin to control as many LEDs as you like. Eac...

SKU: AF-1558 · MPN: 1558

So, you want lots and lots of NeoPixels? And you want them for less? Not a problem! Here's a sheet of Breadboard-Friendly NeoPixel breakouts fresh from the (reflow) oven. Snap them off as you need 'em and save a pretty penny while you're at it.Each order comes with 25 pixels on a snap-apart sh...

SKU: AF-1312 · MPN: 1312

This is the easiest way possible to add small, bright RGB pixels to your project. We took the same technology from our Flora NeoPixels and made them breadboard friendly, with two rows of 3 x 0.1" spaced header on each side for easy soldering, chaining and breadboarding. These ultra-bright LEDs...

SKU: SF-DEV-17745

The SparkFun Thing Plus - RP2040 is a low-cost, high performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or Feather footprint (with 18 GPIO pins), the board also includes an SD card slot, 16MB (128Mbit) flash...

SKU: PI-A000005

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x).It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard ...

SKU: EC-MCA03168A

The Nano 168 is a compact, breadboard-friendly Arduino-compatible development board based on the ATmega168 microcontroller. It offers the same functionality as the Arduino Nano in a small DIP form factor, with 14 digital I/O pins, 8 analogue inputs, and Mini-B USB for programming and serial commu...

SKU: DF-SEN0171

A passive infrared (PIR) motion sensor from DFRobot's Gravity series. It detects infrared radiation from people and animals in motion and outputs a digital HIGH signal when movement is detected — ideal for security systems, occupancy sensing, and automated lighting projects. The sensor operates ...

SKU: LB-PT7009-13

This High-Torque MG996R Digital Servo features metal gearing resulting in extra high 10kg stalling torque in a tiny package. The MG996R is essentially an upgraded version of the famous MG995 servo, and features upgraded shock-proofing and a redesigned PCB and IC control system that make it m...