All Products

SKU: AF-4194

A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...

SKU: AF-5971 · MPN: ADA5971

The Adafruit Chainable DS18B20 Extender Breakout makes it easy to connect multiple DS18B20 temperature sensors in a daisy chain using standard STEMMA JST PH 2mm cables. Each breakout includes screw terminal blocks for direct connection of DS18B20 sensors in TO-92 or waterproof cable form — no sol...

SKU: AF-4712

The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...

SKU: AF-5580

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...

SKU: AF-4410

The Adafruit Micro-Lipo Charger is a tiny, easy-to-use charger for single-cell 3.7V/4.2V lithium polymer and lithium ion rechargeable batteries. Simply plug a USB-C cable into any USB power source and connect your battery via the JST connector — two LEDs show charging status at a glance (red = ch...

SKU: SF-PRT-09750

A 3-pin right-angle JST PH series through-hole connector with 2mm pin spacing. These compact connectors provide a solid locking connection and are rated for moderate current, making them a reliable choice for PCB-mounted sensor and peripheral connections. Commonly used to interface with Sharp in...

SKU: AF-1862

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate w...

SKU: AF-783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: AF-4029

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA ...

SKU: AF-5892 · MPN: ADA5892

This breakout makes it much easier to use the tiny MAX4544 SPDT analogue switch in prototypes and one-off builds. It gives you a solid-state alternative to a relay for switching between two analogue signal paths, with a compact board and a plug-and-play STEMMA JST PH input so you can get started ...

SKU: AF-5940 · MPN: ADA5940

This breakout uses Vishay's TSSP77038 infrared demodulator to give you the raw demodulated output from a 38kHz IR signal, without the extra filtering used in typical remote-control receivers. That makes it a handy choice for reflective sensing, light barriers, fast proximity detection, and modula...

SKU: SF-GPS-00579

A 6-pin vertical JST SH connector in a surface-mount (SMD) package. With a 1.0mm pitch, this is a compact connector ideal for space-constrained PCB designs where a small, reliable connection is needed. This is the JST SH type (1.0mm pitch), which is smaller than the standard JST PH (2.0mm) conne...

SKU: AF-1863

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, and one pin that ...

SKU: AF-4493

For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching  JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch. Simply plug the cable in, then use the black wire to c...

SKU: AF-5970 · MPN: ADA5970

The Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout detects IR signals across a wide frequency range of 20–60 KHz, making it perfect for "code learning" applications where you need your device to work with any IR remote control — even when you don't know the carrier frequency. U...

SKU: AF-6406 · MPN: ADA6406

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitc...

SKU: AF-6404 · MPN: ADA6404

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitc...

SKU: AF-6475 · MPN: ADA6475

Make an internet-connected RGB matrix display without the usual wiring fuss. This board plugs straight into the back of a compatible HUB75 RGB matrix, giving you an easy way to build colourful signs, clocks, status panels and data dashboards with CircuitPython or Arduino.This version uses a u.FL ...

SKU: AF-4927

A slim, reliable 1.25 mm pitch cable with 7-pin connectors on both ends and a 20 cm length. The friction-lock connectors provide a secure, satisfying click for lightweight connectivity where standard 0.1" headers or JST PH connectors are too bulky. This cable uses 1:N reversed wiring, meaning pi...

SKU: AF-4928

A slim, reliable 1.25 mm pitch cable with 8-pin connectors on both ends and a 20 cm length. The friction-lock connectors provide a secure, satisfying click for lightweight connectivity where standard 0.1" headers or JST PH connectors are too bulky. This cable uses 1:N reversed wiring, meaning pi...