All Products
Showing 1-20 of 60 products
9V battery holder with switch 5.5mm/2.1mm plug
A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...
Waterproof 2xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
Waterproof 3xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
6 x AA battery holder with 5.5mm/2.1mm plug
A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells for 7.2V at ~2000mAh. The 9V alkaline output is ideal for boards with a 5V volta...
micro:bit Classroom Class Pack (30 Students) Kit
·
Everything a teacher needs for a one-micro:bit-per-student classroom: 30× BBC micro:bit v2 boards, 30× colour-coded USB cables, 30× AAA battery holders, and 30× protective cases — ready to hand out, plug in, and code. Ideal for primary and secondary Digital Technologies, Design & Technologies, a...
9V battery holder without DC connector
A simple single-slot 9V battery holder case with wire leads for soldering or connecting directly to your projects. Keeps your battery secure and organised. Key Features Wire Leads – Pre-attached cables for direct soldering or breadboard connection Snap-Fit Design – Holds one standard 9V batte...
8-AA Battery Holder, Back-to-Back
A battery holder for eight AA cells, arranged as two back-to-back four-cell holders. Provides up to 12V (with alkaline cells) in a compact, stackable form factor. Specifications Cell Type – AA Capacity – 8 cells Configuration – Two 4-cell holders, back-to-back Output – Up to 12V (series, al...
9V Battery Snap
A compact 9V battery clip for providing portable power to your circuits. The clip is robust and insulated, offering a safe and solid connection for either a 9V battery or compatible battery packs. Key Features Insulated Housing – Safe, protected connection to your battery Versatile Use – Work...
Adafruit Beginner LED Sewing Kit
The Adafruit Beginner LED Sewing Kit has everything you need to start stitching glowing circuits with conductive thread. No soldering or microcontroller required — the included candle-flicker LEDs twinkle automatically for a warm, animated glow. With enough supplies for two projects with two LED...
9V battery clip with 5.5mm/2.1mm plug
A high-quality 9V battery clip with a pre-assembled 5.5mm/2.1mm centre-positive barrel connector. The moulded plastic clip covers the battery terminals to prevent short circuits, and the barrel plug connects directly to Arduino boards and other devices with a standard DC barrel jack. Key Feature...
Adafruit LC709203F LiPoly / LiIon Fuel Gauge and Battery Monitor - STEMMA JST PH QT / Qwiic
The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...
JST-PH 2-Pin SMT Right Angle Connector
This JST PH 2-pin SMT right-angle connector is a surface-mount header designed to accept standard JST PH 2-pin plugs. It's commonly used as a battery connector on microcontroller boards, LiPo chargers, and small electronics — compatible with single-cell LiPo/Li-Ion battery leads, coin cell holder...
Electro-Fashion, Discovery Pack
A starter kit for e-textiles and wearable electronics from Kitronik's Electro-Fashion range. This Discovery Pack includes a curated selection of sewable components — LEDs, switches, coin cell holders, conductive thread, and batteries — everything you need to begin adding electronics to fabric pro...
3.7V 18650 Lithium Battery Tip Head - 2600mAh 2pack
Power your projects reliably with this 3.7V 18650 Lithium Battery 2-pack, featuring a convenient tip head design for easy integration into battery holders and devices. With a 2600mAh capacity, these cells are ideal for portable electronics, DIY builds, and power applications requiring stable, rec...
JST-PH Battery Extension Cable - 500mm
A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...
Metal Rework Station Stand with Two Clips and Four PCB Holders
A weighted metal rework station designed for SMT soldering and electronics repair. The 600 g metal plate keeps your workspace stable, while four magnetic PCB holders secure boards of any shape between 0.2–2 mm thick. Two adjustable alligator clip arms attach at the end of the plate for holding wi...
Primary School Paper Circuits with Screw closed battery
Paper Circuits are a fantastic way to engage a classroom in making and creating. These super simple circuits can be planned out on paper and students will feel accomplished as their creating lights up.This kit contains enough LEDs, Batteries and Copper Tape to make 20 paper circuits. ...
LM66200 Dual Ideal Diode Breakout
·
This compact Adafruit breakout helps manage two power inputs in a small project, such as a battery, USB supply or DC wall adaptor. It uses the LM66200 dual ideal diode IC to select the higher of two inputs while helping prevent back-powering.Connect your two 2–5V supplies to Vin1 and Vin2, and th...
10mm Plastic Bevel LED Holder - Pack of 5
Keep your 10mm LEDs securely mounted with these plastic bevel-style LED holders. Simply slot the LED through the opening and it snaps into place, giving a clean, finished look to your project. Key Features 10mm LED Size – Designed for standard 10mm through-hole LEDs Snap-Fit Design – LEDs cli...
4-Soldering Zoo Animal Kit
A beginner-friendly DIY soldering kit that lets kids build six adorable zoo animal circuits. Each pre-cut PCB animal gets a colour-changing RGB LED and coin cell battery soldered on the back, bringing it to life with a soft blinking light. A great introduction to soldering, circuits, and electron...
