All Products

SKU: AF-449

This 8×AA battery holder provides a portable 12V power source by connecting 8 AA batteries end-to-end in series. It delivers approximately 12VDC with alkaline cells (9.6V with NiMH rechargeables) and supports up to 2A peak current draw. The holder securely retains the batteries even when bumped ...

SKU: AF-875

This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...

SKU: EF-EF10111

A crystal-clear acrylic enclosure for the BBC micro:bit with an integrated 2×AA battery holder on the back. The two-piece case wraps the micro:bit while leaving the A and B buttons and edge connector gold fingers fully exposed for easy access. Key Features Material – Crystal acrylic, two-piece...

SKU: PL-1161

A battery holder for eight AA cells, arranged as two back-to-back four-cell holders. Provides up to 12V (with alkaline cells) in a compact, stackable form factor. Specifications Cell Type – AA Capacity – 8 cells Configuration – Two 4-cell holders, back-to-back Output – Up to 12V (series, al...

SKU: DF-FIT0619

This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devices that use the PH2.0 power interface. Key Features 3× AA Series Configurati...

SKU: AF-4779

This compact battery holder connects 3× AA batteries in series, providing 3.3–4.5V output — a similar range to lithium-ion/polymer batteries. It features a built-in on/off switch and a genuine JST-PH 2-pin connector with a 6" cable, making it a convenient drop-in power source for 3.3V projects wi...

SKU: AF-3905

This compact 2×2 AA battery holder connects four AA batteries in series, providing a nominal 6 V DC output (alkaline) or 4.8 V DC (rechargeable NiMH). The premium jumper header wires plug directly into a breadboard — no stripping or soldering required for prototyping. The square 2×2 configuratio...

SKU: SF-PRT-07949

A PCB-mount clip designed to hold a single AA battery. Ideal for small, low-power applications that need a compact battery solution. Sold individually — use two clips for a complete AA battery holder. Key Features PCB Mount (PTH) – Through-hole solder pins for secure board mounting Single AA ...

SKU: AF-3858

A 2×AA battery holder with premium jumper header wires that plug directly into a breadboard — no stripping, twisting, or fighting with thin leads. Two AA batteries in series provide approximately 2.5V to 3V, making this a convenient power source for breadboard prototyping. Key Features Breadbo...

SKU: AF-4193

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...

SKU: AF-3287

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...

SKU: LB-BATTERYAA

A 2× AA battery holder with on/off switch, designed for powering the BBC micro:bit on the go. The JST connector plugs directly into the micro:bit's battery port, and the ~14 cm cable provides enough length for flexible mounting. Key Features 2× AA Battery Holder – Provides 3 V from standard AA...

SKU: TB-PH9203

A single AA battery holder moulded in Delrin with corrosion-resistant nickel-plated springs and studs. It comes with 150 mm bare lead connection wires for easy integration into your projects. Specifications Cell Type – AA Number of Cells – 1 Output Connection – Bare leads Cable Length – 150...

SKU: PL-1155

A compact enclosed battery holder for six AA batteries, providing approximately 9V (alkaline) or 7.2V (NiMH rechargeable) from a series configuration. Features bare wire leads for flexible integration into your project. Key Features 6-Cell Capacity – Holds six AA batteries in series Enclosed ...

SKU: AF-4194

A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...

SKU: AF-3788

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4....

SKU: AF-3859

A 4×AA battery holder with premium jumper header wires that plug directly into a breadboard. No stripping or soldering required — just insert the header pins into your breadboard rails and start prototyping with portable battery power. Delivers approximately 4.8V with NiMH rechargeable batteries...

SKU: AF-248

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells for 7.2V at ~2000mAh. The 9V alkaline output is ideal for boards with a 5V volta...

SKU: AF-3784

A 4×AA battery holder with a 20cm (8″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides a portable power source for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4.8V with NiMH rechargeable batteries or up to 6V wit...

SKU: DF-EDU0170

The Gravity Science Data Acquisition Module Kit is a comprehensive toolkit for conducting digital scientific experiments without programming or electronics knowledge. Built around the DFRobot SCI DAQ module, it includes four sensors covering soil moisture, ambient light, temperature/humidity, and...