All Products
AI Overview
Here are the main Pololu options that match this search, grouped by common use:
Motor drivers (Raspberry Pi / Arduino)
- For Raspberry Pi and higher-current brushed DC motors: Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled) — up to 14A continuous/channel, up to 24V ($113.30).
- For Raspberry Pi and smaller motors: Dual MAX14870 Motor Driver for Raspberry Pi — 4.5–36V, up to 1.7A continuous/channel ($31.50).
- For Arduino motor control in shield form factor: Pololu Dual G2 High-Power Motor Driver 18v18 Shield for Arduino — dual high-power H-bridges for brushed DC motors ($94.50).
Power (step-down regulators)
- For regulated 5V rails from higher-voltage batteries/supplies: Pololu 5V, 2.5A Step-Down Voltage Regulator D24V22F5 — up to 36V input, 2.5A ($45.00).
- For regulated 12V output: Pololu 12V, 2.2A Step-Down Voltage Regulator D24V22F12 — up to 36V input, 2.2A ($27.95).
Motors & motion hardware
- Geared motor with feedback: 34:1 Metal Gearmotor 25Dx52L mm HP 12V with 48 CPR Encoder — 12V, 34:1 gearbox, 48 CPR quadrature encoder ($74.15).
- Small robot wheels: Pololu Wheel 40x7mm Pair - Red — 40mm diameter, press-fit for 3mm D-shafts ($9.10).
- Motor mounting: Pololu Micro Metal Gearmotor Bracket Extended Pair — mounting bracket set for Pololu micro metal gearmotors ($8.30).
- Caster support: Pololu Ball Caster with 1" Plastic Ball and Ball Bearings — ball caster for small robot chassis ($19.50).
- Shaft/wheel coupling hubs: Pololu Universal Aluminum Mounting Hub for 5mm Shaft, #4-40 Holes (2-Pack) — 5mm shaft hubs ($19.60); Pololu Universal Aluminum Mounting Hub for 8mm Shaft, M3 Holes (2-Pack) — 8mm shaft hubs ($14.25).
Sensors & switching
- Gas sensor carrier: Pololu Carrier for MQ Gas Sensors (Bare PCB Only) — breakout/carrier for MQ-series gas sensors ($2.25).
- Relay switching modules: Pololu Basic SPDT Relay Carrier with 5VDC Relay (Partial Kit) ($4.00), Pololu Basic SPDT Relay Carrier with 12VDC Relay (Assembled) ($9.95), and Pololu Basic 2-Channel SPDT Relay Carrier with 5VDC Relays (Assembled) — 2-channel SPDT ($17.05).
What type of Pololu part are you looking for?
Collections
Showing 141-160 of 252 products
Motoron M3H256 Triple Motor Controller for Raspberry Pi (Connectors Soldered)
The Motoron M3H256 Triple Motor Controller makes it easy to control DC motors from a Raspberry Pi (Model B+ or newer) through an I²C interface. Each module can independently control up to three motors, and multiple Motoron boards can be stacked on top of the same Raspberry Pi for projects that ne...
Motoron M3S256 Triple Motor Controller Shield for Arduino (Connectors Soldered)
The Motoron M3S256 Triple Motor Controller Shield for Arduino makes it easy to control DC motors from an Arduino or Arduino-compatible board through an I²C interface. Each module can independently control up to three motors, and multiple shields can be stacked on top of the same Arduino for proje...
VL53L0X Time-of-Flight Distance Sensor Carrier with Voltage Regulator, 200cm Max
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away. The VL53L0X uses time-of-flight measurements of infrared pulses for ranging, allowing it to give accurate results independent of the target’s color and s...
Motoron M3H256 Triple Motor Controller for Raspberry Pi (No Connectors or Standoffs)
The Motoron M3H256 Triple Motor Controller makes it easy to control DC motors from a Raspberry Pi (Model B+ or newer) through an I²C interface. Each module can independently control up to three motors, and multiple Motoron boards can be stacked on top of the same Raspberry Pi for projects that ne...
AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier)
The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...
Pololu Wheel 40x7mm Pair - Red
A pair of red plastic wheels with silicone tires, designed for small robotics projects. These 40mm diameter wheels press-fit directly onto 3mm D-shafts, making them a perfect match for Pololu micro metal gearmotors and mini plastic gearmotors. The silicone tires provide good grip on smooth surfa...
Pololu Adjustable Boost Regulator 4-25V
Overview The Pololu adjustable boost regulator is a very flexible switching regulator (also called a switched-mode power supply, SMPS, or DC-to-DC converter) that can generate voltages higher than its input voltage. We offer two adjustable ranges: approximately 2.5 V to 9.5 V and ...
Pololu RC Switch with Small Low-Side MOSFET
The Pololu RC Switch with Small Low-Side MOSFET converts standard hobby RC receiver outputs into simple on/off signals. It measures incoming RC pulse widths against a configurable threshold to control an integrated MOSFET, allowing you to drive small loads like LEDs, relays, or motors directly fr...
Pololu Serial 8-Servo Controller (assembled)
The Pololu Serial 8-Servo Controller lets you control up to eight RC servos from almost any robot controller, microcontroller, or computer with a serial port. It accepts standard RS-232 or TTL-level serial signals with automatic baud rate detection from 1200 to 38400 bps. Multiple controllers ca...
Pololu 5V, 5A Step-Down Voltage Regulator D24V50F5
The Pololu D24V50F5 is a high-efficiency step-down (buck) voltage regulator that converts input voltages up to 38V down to a fixed 5V output. With a typical maximum output current of 5A and efficiency between 85% and 95%, it far outperforms linear regulators — especially when the input-to-output ...
Pololu Aluminum Scooter Wheel Adapter for 1/4 Shaft
This two-part aluminum assembly mounts directly to 1/4 inch diameter motor output shafts like those on our NEMA 23 stepper motors and allows you to drive most scooter, skateboard, inline skate, and other common wheels that are compatible with popular 608 ball bearings. Two M4 set screws are...
Pololu 5V, 300mA Step-Down Voltage Regulator D24V3F5
The Pololu D24V3F5 is a compact buck (step-down) switching voltage regulator that converts input voltages up to 42 V down to a fixed 5 V output. With a typical efficiency of 80–90%, it significantly outperforms linear regulators like the 7805, especially when there is a large difference between i...
Pololu 5V Step-Up/Step-Down Voltage Regulator S7V7F5
The Pololu S7V7F5 is a compact buck-boost switching voltage regulator that accepts a wide input range of 2.7 V to 11.8 V and produces a fixed 5 V output with typical efficiency over 90%. It automatically steps up or steps down the input voltage as needed, making it ideal for battery-powered appli...
Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, Pi A+, Pi 2, or Pi 3 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Its integrated DRV8835 dual motor driver allows it to operate from 1.5 V to 11 ...
Pololu 12V, 2.2A Step-Down Voltage Regulator D24V22F12
The D24V22Fx family of step-down voltage regulators generates lower output voltages from input voltages as high as 36 V. They are synchronous switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) with typical efficiencies of 85% to 95%, which is much more e...
Pololu 3.3V, 300mA Step-Down Voltage Regulator D24V3F3
The compact (0.4″ × 0.5″) D24V3F3 switching step-down (or buck) voltage regulator takes an input voltage between 4.3 V and 42 V and efficiently reduces it to 3.3 V while allowing for a maximum output current of 300 mA. The pins have a 0.1″ spacing, making this board compatible with standard so...
Pololu Ball Caster with 1" Plastic Ball and Ball Bearings
This ball caster is an improved version of our original Pololu Ball Caster with 1″ Plastic Ball; we recommend this new version over the older version for all applications that are not somehow specifically tied to the previous design.This ball caster kit includes a two-part black ABS housing, a 1″...
Pololu Basic SPDT Relay Carrier with 12VDC Relay (Assembled)
The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB with a soldered-in 12 V relay, 5.0 mm terminal blocks for the switch connections, and stra...
Pololu Dual G2 High-Power Motor Driver 18v18 Shield for Arduino
The Pololu Dual G2 High-Power Motor Driver 18v18 Shield uses pairs of discrete MOSFET H-bridges to drive two large brushed DC motors. It has an Arduino shield form factor for direct plug-in use, and also breaks out all motor driver pins along the left side for standalone operation without an Ardu...
Pololu Carrier with Sharp GP2Y0D815Z0F Digital Distance Sensor 15cm
This small digital distance sensor detects objects between 0.5 cm and 15 cm (0.2″ and 6″) away. With its quick response time, small size, low current draw, and short minimum sensing distance, this sensor is a good choice for non-contact, close-proximity object detection, and our compact...
