All Products
Showing 21-40 of 54 products
Three Wire Display Stand for Raspberry Pi Book IPad or Galaxy
This handy Three Wire Display Stand is made for Raspberry Pi, but also can adapt to other tablet PC, such as iPad. It is great for general electronics & TFT holding. You can adjust the angle as you like. Features Fully adjustable Vinyl Coated Steel Wire that will not scratch furniture or disp...
Tamiya 70171 3mm Threaded Shaft Set
The Tamiya 70171 3mm Threaded Shaft Set includes two fully-threaded 3 × 150mm shafts with ball joints and connectors for building control rods with three-dimensional movement. The shafts can be cut to any desired length, making them versatile for linkages, pulley mounting, and mechanical assembli...
Adafruit 555 PWM Output STEMMA - 1.5K~25 KHz or 1.5~250 Hz
·
The Adafruit 555 PWM Output STEMMA is a fully assembled 555 timer board that generates an adjustable square-wave PWM signal — no breadboard wiring or external components needed. An onboard trimmer pot lets you tune the frequency across two selectable ranges: approximately 1.5 KHz to 25 KHz, or 1....
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
·
A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully assembled and tested with a 20–20 kHz electret microphone soldered on. A trimmer p...
Qwiic Soil Moisture Sensor
·
This compact breakout board measures moisture in soil and similar materials using two large exposed pads as conductivity probes. As the soil gets wetter, conductivity between the pads increases, resistance drops, and the sensor produces a higher analog SIG output.For quick setup, the board includ...
Mini MP3 Player
DFPlayer Mini is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module can be used alone with battery power supply, speaker and keypad, or through the serial port control, as the Arduino UNO or any microcontroller with a serial port module. The module itself p...
16x8 1.2 LED Matrix + Backpack - Ultra Bright Square White LEDs
·
The 16×8 1.2" LED Matrix + Backpack combines two ultra-bright square white 8×8 LED matrices on a single, compact driver board. The square pixel design creates a seamless, uniform look — perfect for scrolling text, small animations, or status displays in your projects. Powered by the HT16K33 driv...
16x8 1.2 LED Matrix + Backpack -Ultra Bright Square Yellow LEDs
·
The 16×8 1.2" LED Matrix + Backpack combines two ultra-bright square yellow 8×8 LED matrices on a single, compact driver board. The square pixel design creates a seamless, uniform look — perfect for scrolling text, small animations, or status displays in your projects. Powered by the HT16K33 dri...
16x8 1.2 LED Matrix + Backpack - Ultra Bright Square Green LEDs
·
The 16×8 1.2" LED Matrix + Backpack combines two ultra-bright square pure green 8×8 LED matrices on a single, compact driver board. The square pixel design creates a seamless, uniform look — perfect for scrolling text, small animations, or status displays in your projects. Powered by the HT16K33...
16x8 1.2 LED Matrix + Backpack - Ultra Bright Square Blue LEDs
·
The 16×8 1.2" LED Matrix + Backpack combines two ultra-bright square blue 8×8 LED matrices on a single, compact driver board. The square pixel design creates a seamless, uniform look — perfect for scrolling text, small animations, or status displays in your projects. Powered by the HT16K33 drive...
Adafruit TPL5110 Low Power Timer Breakout
·
The Adafruit TPL5110 Low Power Timer Breakout turns any electronics project into a low-power system by periodically switching power on and off. Connect it between your power supply and your project, and the TPL5110 will handle the rest — powering up your circuit at configurable intervals from eve...
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
DFPlayer - An Arduino Mini MP3 Player
Sing for the moment! The DFPlayer Mini is a small and low cost MP3 module player with an simplified output directly to the speaker. The module can be used as a stand alone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other with ...
8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards
·
The 8-Channel PWM or Servo FeatherWing adds 8 channels of 12-bit PWM output to any Adafruit Feather board via I2C. It uses an onboard PWM driver with a built-in clock, so it runs independently without tying up your microcontroller — unlike the TLC5940 family, no continuous signal is needed. The ...
16x8 1.2 LED Matrix+Backpack UltraBright Round YellowGreen LEDs
·
The 16×8 1.2" LED Matrix + Backpack combines two ultra-bright round yellow-green 8×8 LED matrices on a single, compact driver board. The classic round pixel design gives a retro dot-matrix aesthetic — ideal for scrolling text, small animations, or status displays in your projects. Powered by the...
LIDAR-Lite v3HP
The LIDAR-Lite v3HP is a compact, high-performance optical distance measurement sensor from Garmin. Housed in a durable IPX7-rated enclosure, it delivers accurate range measurements from 5 cm to 40 m, making it an ideal solution for drones, robots, and unmanned vehicles. Compared to the LIDAR-Li...
M5StickC ADC HAT ADS1100
Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, delta-sigma A/D converter. Extremely easy ...
SparkFun 16x2 SerLCD - RGB Text (Qwiic)
The SparkFun 16×2 SerLCD is a serial-enabled LCD that provides a simple, cost-effective way to add an RGB-on-black liquid crystal display to your project. An on-board ATmega328P microcontroller handles all screen control, eliminating the need for a separate backpack board. The display supports t...
Mini Basic PIR Sensor - BS412
·
A compact passive infrared (PIR) motion sensor that detects movement from approximately 3–8 metres away. Much smaller than standard PIR modules, making it ideal for unobtrusive, space-constrained projects. Fully self-contained — just needs power, ground, and a resistor to set the delay time. Key...
Adafruit Universal USB / DC / Solar Lithium Ion/Polymer charger - bq24074
·
The Adafruit Universal USB/DC/Solar Lithium Ion/Polymer Charger (bq24074) charges 3.7V/4.2V LiPo or LiIon batteries from virtually any power source — USB Type-C, DC adapter, or solar panel — with a wide 5–10V input range. Its near-MPPT solar tracking automatically draws the maximum current availa...
