All Products

SKU: DF-FIT0856

This DB9 Male to RJ45 Female Adapter can be used to handle serial data communication between RS232 devices with one RJ45 network cable, or as an extender to extend RS232 serial signal to about 20m.Two modules are required for serial port to network cable transmission. It enables to extend serial ...

SKU: DF-FIT0429

INTRODUCTION OBD II is an On-Board Diagnostics standard that is used on a large variety of cars. It provides access to numerous data from the engine control unit (ECU) and offers a valuable source of information when troubleshooting problems inside a vehicle. This is an OBD-II to DB9 cable, ...

SKU: DF-SEN0522

This human body sensing switch adopts an infrared detection way to control load switch. It offers a detection range of 5~8m, high sensitivity, and reliability. The sensor has an adjustable delay function and the input and output voltages are the same. It is widely used in various automatic i...

SKU: EC-PMMA19005G

A DC 12 V four-way solenoid valve with one inlet and four independently controlled outlets. Each outlet has its own control wire, so you can open any combination of the four channels — use one at a time or all four simultaneously. Designed for automated plant watering, aquarium systems, and other...

SKU: DF-FIT0884

This DC 5.5×2.1mm power splitter cable lets you power two DC devices from a single power source. Each cable splits one female DC jack into two male DC plugs, making it easy to share a power adapter between devices. Built with tinned oxygen-free copper wire for stable transmission and minimal sig...

SKU: DF-FIT0885 · MPN: FIT0885

This DC power splitter cable lets a single DC 5.5 x 2.1 mm power source feed three compatible devices, making it a handy option for tidy multi-device power setups.It uses a tinned oxygen-free copper wire core for stable transmission and to help suppress external signal interference. The PVC outer...

SKU: DF-FIT0886 · MPN: FIT0886

This DC power splitter cable lets you run four DC devices from a single power source. It has one DC 5.5 x 2.1mm female connector splitting out to four DC 5.5 x 2.1mm male connectors, making it handy for tidier low-voltage power distribution.The cable is compatible with DC5.5*2.1 connectors and us...

SKU: EC-RPA01305R

This cooling fan is designed for Raspberry Pi Model B+ / Raspberry Pi B. With this useful fan, you don’t need to worry about your pi becoming too hot, it can help to protect the Raspberry Pi well. The power charger should be DC 5V 0.13A.Specifications Power Connection: 2 PIN Rated Voltage: DC 5V ...

SKU: SF-PRT-10811

This DC power jack/connector is just like the other one that we carry except that it’s terminated with breadboard-friendly pins instead of wide solder terminals. These are also compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter.Documents:Dimensional Drawing

SKU: DF-FIT0151

A screw-terminal adapter that converts a 5.5 × 2.1 mm centre-positive DC barrel jack connection to bare wire terminals. Plug in a barrel jack power supply on one end and connect the screw terminals to a breadboard, circuit, or project on the other — a simple way to add a standard DC power input w...

SKU: SF-PRT-10288

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.

SKU: DF-FIT0110

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution. Wi...

SKU: SF-PRT-10287

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.

SKU: SF-PRT-13126

This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1mm barrel connectors. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.

SKU: SF-PRT-11476

This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.Do...

SKU: PL-2449

This connector adapts a 5.5 × 2.1 mm DC barrel jack to a pair of screw terminals spaced approximately 5 mm (0.2″) apart. The terminals are labeled positive and negative, with the positive terminal connected to the center pin.

SKU: SF-PRT-00119

DC power jack/connector. This is a common barrel-type power jack for DC wall supplies. These are compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter. Datasheets: Datasheet

SKU: PI-COM1303

DC power jack/connector. This is a common barrel-type power jack for DC wall supplies. These have a 5.5mm jack, with a 2.1mm center pole diameter. Datasheets: Datasheet

SKU: SF-PRT-12748

A standard SMD (surface-mount) DC barrel power jack for use with common DC wall adapters. This is the same connector size used on most Arduino boards and many other development platforms. Key Features Surface-Mount (SMD) – Reflow-solderable for custom PCB designs Standard Size – 5.5 mm outer ...

SKU: LB-LR0214-142A

One input: DC 6V - 12V (input voltage to the output voltage must be higher than 1V.) Output: 3.3V (+ - 0.05v error), 5.0V (+ - 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly converter to the output) PCB board size: 4.5cm * 4.5cm With red power indicator le...