All Products

SKU: DF-FIT0833

This gold-plated IPEX to SMA female connector has passed 48 hours salt spray test, which is durable and not easy to rust.It adopts RG1.13 wire material and high-density shielding layer, soft and firm, fold-resistant and durable, with fast and stable data transmission.These IPEX to SMA Female Cabl...

SKU: DF-FIT0872

A gold-plated IPEX (U.FL) to SMA male (inner needle) pigtail cable for connecting wireless modules to external antennas. The gold-plated connectors have passed 48-hour salt spray testing for long-lasting corrosion resistance. Built with RG1.13 wire and a high-density shielding layer, this cable ...

SKU: AF-2167 · MPN: 2167

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to ...

SKU: DF-SEN0503

An infrared break-beam sensor pair for simple, reliable motion detection. The emitter sends a beam of invisible IR light to the receiver — when an object passes between them and breaks the beam, the receiver outputs a signal. Works up to 50 cm at 5 V with a fast response time under 2 ms. The com...

SKU: AF-2168 · MPN: 2168

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to IR,...

SKU: AF-164 · MPN: 164

The Sharp GP2Y0A21YK0F is an infrared distance sensor that measures distances from 10 cm to 80 cm by bouncing IR light off objects. It outputs an analogue voltage proportional to distance — approximately 3 V at 10 cm and 0.4 V at 80 cm — which can be read directly by an Arduino or other microcont...

SKU: AF-1031 · MPN: 1031

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 8" long 3-JST interface wire. These sensors are good for detection between 20cm-150cm. For over 1 m distance...

SKU: SF-COM-29198 · MPN: COM-29198

The IRF7509 is a common N- and P-channel MOSFET device for switching higher-power loads from low-power control signals. Its low on-resistance helps reduce losses, while the logic-level gate is suited to control from many 5V microcontrollers or mechanical switches.This surface-mount MOSFET is usef...

SKU: LB-FLAME-LIGHT

This IR flame sensor module detects flames and infrared light sources in the 760–1,100 nm wavelength range. With a detection angle of approximately 60° and a test range of up to 80 cm (depending on flame size), it provides both digital and analogue output for flexible integration with Arduino, Ra...

SKU: SF-GPS-16838

The M1600HCT-P-SMA is a dual-band passive antenna that combines Iridium satellite communication with L1 GNSS reception (GPS and GLONASS) in a single compact unit. Ideal for tracking devices that transmit their position over the Iridium network. Weighing just 11 grams with a built-in O-ring, the ...

SKU: LB-LR0062

This IR sensor can detect obstacles in front of it.  When an object is detected the green indicator light on the board will light up. There is a low-level output signal on the OUT port.It has a detection range of 2-30 cm at an angle up to 35 degrees.The detection distance can be changed by u...

SKU: AF-157 · MPN: 157

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just pass...

SKU: SF-SEN-10266

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP382 is a miniaturized receiver for infrared remote control systems. A PIN d...

SKU: LB-LR0097-1-NEW

This infra-red receiver module is perfect for Arduino projects. It has a wide range of applications, including remote control, wireless data transmission, etc.

SKU: SF-COM-09542

The QRE1113 is a small IR reflectance sensor. This sensor is often used in line following robots because, if it can sense if a surface is white or black. There are four pins on the QRE1113 - two control the IR emitting LED while the other two are the collector and emitter of a phototransisto...

SKU: LB-LS6779

This Remote takes 2 x AAA batteries making it safe to use in schoolsIt has 12 buttons that can be pressed and will send an IR signalThis remote is now included with many of our kits and sends the following signalsOn       129=          131Home  11...

SKU: LB-IR-REMOTE

Introducing the perfect addition to your robotics classroom - the IR Remote Control for use with Maqueen and Owl Robots! This user-friendly remote is powered by 2 AA batteries and features numbers 0-9 and direction buttons, making it compatible with all of our IR robots and modules.Effortlessly c...

SKU: LB-OWL-IR

An infrared receiver module that can read signals from most standard IR remote controls. Useful for adding remote control functionality to Arduino and microcontroller projects. Pair with an IR transmitter module to build a universal remote control system. Key Features IR Signal Reception – Rea...

SKU: WS-31940 · MPN: 31940

Elevate your technological projects with our cutting-edge Long-wave IR Thermal Imaging Camera Module. Designed for seamless integration with Raspberry Pi and other development boards, this module is an ideal addition for engineers, developers, makers, and hobbyists looking to implement advanced t...

SKU: SF-COM-29556 · MPN: COM-29556

The IS66WVS16M8FBLL-104NLI is an integrated PSRAM memory IC with 128 Mbits of pseudo static RAM, organised as 16 Megabytes words by 8 bits. It uses a self-refresh DRAM array and is built as a dual die stack of two 64Mb die.This device supports both SPI (Serial Peripheral Interface) and QPI (Quad ...