All Products

SKU: SF-PRT-13032

A simple breadboard power supply that takes a 6–12 V input and outputs a regulated 5 V or 3.3 V. All headers are at 0.1" pitch for direct insertion into a standard breadboard, with the output pins spaced to power both breadboard power rails simultaneously. Input power connects via the DC barrel ...

SKU: SF-COM-15208

The SparkFun Buck-Boost Converter is a handy power accessory board that allows you to fine tune the amount of power your project receives. This converter can take an input voltage of anywhere from 3-16V which can then be regulated to an output voltage between 2.5-9V. With the switch on the bottom...

SKU: SF-COM-21338

The SparkFun 1.8V Buck Regulator Breakout features the AP3429A step-down DC-DC converter, providing a regulated 1.8V output at up to 2A continuous current from a 2.7V to 5.5V input. An enable pin allows the output to be switched on and off programmatically. The 1" × 1" board offers multiple powe...

SKU: SF-COM-21337

The SparkFun 3.3V Buck Regulator Breakout features the AP3429A from Diodes Inc., a 2A step-down DC-DC converter with an input voltage range of 2.7V to 5.5V. This full-size, 1in. x 1in. version of our buck regulator boards is configured to provide a regulated 3.3V output (from a 3.9 to 5.5V input ...

SKU: SF-COM-21255

The SparkFun 5V Buck Regulator Breakout features the AP63357 from Diodes Inc., a 3.5A synchronous buck converter with a wide input voltage range of 3.8V to 32V. The fully integrated 74mΩ high-side power MOSFET/40mΩ low-side power MOSFET provides a high-efficiency step-down DC/DC conversio...

SKU: SF-SEN-14520

The SparkFun Capacitive Touch Breakout provides a single momentary touch button using the AT42QT1011 capacitive sense chip. Simply supply 1.8–5 V and ground — the chip handles all touch monitoring and outputs a digital high signal when a touch is detected, low when released. Unlike the AT42QT101...

SKU: SF-SEN-15344

Do you want to replace a slider or a button on your art project or science experiment with a more interesting interface? This Capacitive Touch Slider is a "Qwiic" and easy way to add capacitive touch to your next project. With the board's built in touch pads, you can immediately start playing wit...

SKU: SF-COM-25893

This is a 5mm right angle light pipe to get the light of an LED out the end plate of an enclosure. We couldn't find a light pipe that fit all our needs, so we made it! This clip snaps over any SMD LED that is 1206 size or smaller. Addressable LEDs 2x2mm or smaller work great! The clip is easily i...

SKU: SF-SEN-22395

The SparkFun SCD40 breakout board measures CO₂ concentration, humidity, and temperature using Sensirion's PASens photoacoustic measurement technology. The sensor detects CO₂ from 0 to 40,000 ppm with high accuracy over the 400–2,000 ppm range, and includes an integrated CMOSens temperature and hu...

SKU: SF-SEN-22396

This SparkFun CO2 Humidity and Temperature Sensor features the next-generation SCD41 photoacoustic CO2 sensor for high-accuracy environmental readings. The SCD41 uses Sensirion's PASens® photoacoustic measurement system that combines narrow-band IR light and a microphone inside the sensing packag...

SKU: SF-BOB-14874

The SparkFun TSH82 Configurable OpAmp Board was designed to give you the best combination of performance and flexibility that we could achieve by giving you two gain stages, each one independently accessible on the header pins. Each stage is natively configured as an inverting amplifier that c...

SKU: SF-DEV-16129

The SparkFun controller:bit is a fun-filled "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional controller system. Designed in a similar form factor to the classic Nintendo controller, the controller:bit is equipped with a four-direction ...

SKU: SF-BOB-12052

Odometers are extremely useful for cars, they tell you how far you have gone, wouldn’t it be nice if you were able to have a device that does the same for electrical current? The LTC4150 SparkFun Coulomb Counter Breakout is here to be your odometer for current. If you are wondering: a coulomb is ...

SKU: SF-DEV-15573

The SparkFun ATECC508A Cryptographic Co-processor Breakout allows you to easily add strong authentication security to your IoT node, edge device, or embedded system. It includes two Qwiic ports for plug and play functionality. Utilizing our handy Qwiic system, no soldering is required to connect ...

SKU: SF-DEV-18077

🛇 Product Restrictions: To access certain features of the ATECC608A, users will need to contact Microchip and sign an NDA contract to obtain the complete datasheet. Due to the required NDA - technical support, an Arduino library, and hookup guide are not provided for users on this product. The...

SKU: SF-SEN-13679

The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of ...

SKU: SF-SEN-12040

The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the...

SKU: SF-DEV-22462

The SparkFun DataLogger IoT is a data logger that comes preprogrammed to automatically log GPS and various pressure, humidity, and distance sensors. All without writing a single line of code! The DataLogger automatically detects, configures, and logs Qwiic sensors. It was specifically designed fo...

SKU: SF-BOB-10160

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. The RTC maintains seconds, minutes, hours, day, date, month, and year information....

SKU: SF-KIT-12963

The SparkFun Digital Sandbox Add-On kit extends the Digital Sandbox (DS) learning platform with three additional circuit experiments. Build an electric musical instrument, control motor speed, and drive a servo — perfect for learners who have completed the first 13 experiments and want more hands...