Great service, reliable product
The Little Bird team were very responsive, my son needed this device urgently for his HSC Major Work. They understood and were very prompt. The sensor itself is reliable, durable, did the task well.
Andrew Wilson
Adafruit
Adafruit BME688 - Temperature, Humidity, Pressure and Gas Sensor
·
All Products
Breakouts
Gas & Air Quality Sensors
Humidity Sensors
New Arrivals
Pressure & Altitude Sensors
Sensors
Temperature Sensors
Adafruit
Brands and Manufacturers
Environmental (temperature, humidity, air quality)
Sensors & Modules
Prototyping & Wiring
$41.90
|
In stock
The BME688 from Bosch delivers comprehensive environmental sensing in a single compact package. This precision sensor measures temperature, humidity, baromet...
Get notified when back in stock
Estimated Delivery
Arrives
Order within 7h 50m for same-day dispatch
Disclaimer
Secure checkout
The BME688 from Bosch delivers comprehensive environmental sensing in a single compact package. This precision sensor measures temperature, humidity, barometric pressure, and VOC gas levels, all accessible over I2C or SPI.
The BME688 is a drop-in replacement for the BME680, adding a programmable gas-sensor heater for controlled odour analysis. This enables machine-learning-based odour detection while retaining all the environmental sensing capabilities of its predecessor. The onboard MOX (metal oxide) sensor detects volatile organic compounds such as ethanol and carbon monoxide, providing an overall VOC resistance value for air quality monitoring.
Key Features
- Temperature – ±1.0°C accuracy
- Humidity – ±3% relative humidity accuracy
- Barometric Pressure – ±1 hPa absolute accuracy
- Altimeter – ±1 metre accuracy (derived from pressure)
- VOC Gas Sensor – Heated MOX element with programmable heater for odour analysis
- Dual Interface – I2C and SPI communication
- STEMMA QT / Qwiic – Plug-and-play I2C connectors, no soldering required
- Voltage Range – 3.3V or 5V operation via onboard regulator and level shifting
Also Available
- Adafruit BME680 – Same sensor family without programmable heater
- Adafruit BME280 – Temperature, humidity, and pressure (no gas sensing)
Ideal For
- Indoor air quality monitoring and odour detection
- Weather stations and environmental logging
- IoT environmental sensing projects
- Machine-learning-based gas classification
Note: Like all VOC/gas sensors, the BME688 has variability and should be calibrated against known sources for precise measurements. Run the sensor for 48 hours on first use to "burn it in", then allow 30 minutes of warm-up each time it is powered on.
Package Contents
- 1× Adafruit BME688 breakout board with headers
Jargon buster
Plain-language definitions for the technical terms used above.
- BME680
- The BME680 is a Bosch environmental sensor chip that measures temperature, humidity, air pressure and a gas signal used to gauge air quality. The part number tells you a device is built around that specific all-in-one sensor, so you can check its library support, accuracy and datasheet details.
- breakout
- A breakout board carries a small or fine-pitched component and brings its connections out to standard, breadboard- and header-friendly pins. Describing a part as a breakout means it can be wired into a project without soldering directly to the component's tiny contacts.
- Headers
- Rows of connector contacts on a fixed pitch (commonly 2.54 mm) used to link a board to a breadboard, jumper wires, or another board. They come as male pin headers and female socket headers; when a module ships with pre-soldered headers it can be used straight away, whereas bare pads require soldering the pins yourself.
- I2C
- I2C is a two-wire communication bus used by many sensors and small modules. It matters because several I2C devices can share the same two wires, but each device needs a compatible address and your controller must support I2C.
- IoT
- Short for Internet of Things, meaning physical devices that connect to networks or the internet to send data or be controlled remotely. It matters if you want projects such as connected sensors, remote controls or classroom data-logging activities.
- Qwiic
- Qwiic is a plug-in connector system for I2C devices that uses small 4-pin cables, so you can connect compatible sensors without soldering. It matters because your controller or adapter also needs Qwiic, or you will need a cable or breakout to wire it up.
- SPI
- A fast serial communication bus often used for displays, memory cards, and sensors. It matters because SPI devices need specific pins for clock and data, plus a separate chip-select line for each device.
- STEMMA QT
- A small plug-in connector system for I2C boards that lets you connect compatible sensors and controllers without soldering. It matters because it can make wiring faster and less error-prone, especially when adding several small modules to a project.
- VOC
- Volatile organic compounds are gases released from things like paints, cleaners, smoke, and some plastics. A VOC reading helps indicate indoor air quality, but it is usually an index or estimate rather than a direct identification of each chemical.
Find this product in
Brands
