Temperature Sensors

SKU: SF-SEN-21262 | Brand: SparkFun

The SparkFun STTS22H is a Qwiic-enabled temperature sensor breakout based on ST Microelectronics' ultralow-power, high-accuracy digital temperature sensor. Factory calibrated to ±0.5°C accuracy without any application...

SKU: DF-SEN0528 | Brand: DFRobot

The AHT20 is a high-precision but low-cost temperature and humidity sensor, which is equipped with an improved MEMS semiconductor capacitive humidity sensor element. It features standard I2C interface and a wide volta...

SKU: DF-SEN0435 | Brand: DFRobot

Compared to DS18B20, LM35, and other common temperature sensors, the MCP9808 is one of the more accurate temperature sensing options, with a typical accuracy of ±0.25°C and maximum accuracy of ±0.5°C over the sensor's...

SKU: DF-SEN0332 | Brand: DFRobot

This Digital Temperature & Humidity Sensor Breakout Board is based upon the Sensirion SHT31-F sensor IC. Thanks to Sensirion’s CMOSens® technology, highly integrated capacitive humidity sensing components and band-gap...

SKU: EF-EF04070 | Brand: ElecFreaks

The Octopus LM35 Analog Temperature Brick is a plug-and-play temperature sensor module based on the TI LM35D precision centigrade temperature sensor. The LM35 outputs a voltage linearly proportional to temperature (10...

SKU: AF-4686 | Brand: Adafruit

The Adafruit TMP235 is a plug-and-play analog temperature sensor with a 3-pin JST PH (STEMMA) connector. Unlike I2C sensors, this one outputs a simple analog voltage proportional to temperature — just connect it to an...

SKU: SF-SEN-16294 | Brand: SparkFun

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junc...

SKU: SF-SEN-16467 | Brand: SparkFun

Looking to keep a log of the climate in your greenhouse, create a humidor control system or want to track temperature and humidity data for a weather station project? The SparkFun SHTC3 Humidity Sensor may be the perf...

SKU: EF-EF04042 | Brand: ElecFreaks

The Octopus DS18B20 Digital Temperature Brick uses the DS18B20 1-Wire digital temperature sensor from Maxim IC to deliver accurate readings from −55 °C to +125 °C with ±0.5 °C accuracy. Each sensor has a unique 64-bit...

SKU: AF-3895 | Brand: Adafruit

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare-wire bead-probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering whi...

SKU: AF-3721 | Brand: Adafruit

The AM2320 is a low-cost digital temperature and humidity sensor with an I2C interface — a simpler alternative to the classic DHT11/DHT22 sensors that require timing-critical bit-bang protocols. With standard I2C comm...

SKU: AF-1727 | Brand: Adafruit

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts t...

SKU: AF-1778 | Brand: Adafruit

The AD8495 from Analog Devices is an analog-output K-type thermocouple amplifier on a compact breakout board. Simply power the board with 3–18V DC, connect a K-type thermocouple to the terminal block, and read the tem...

SKU: SF-SEN-00251 | Brand: SparkFun

36" high temperature Type-K Thermocouple with glass braid insulation.

SKU: AF-3251 | Brand: Adafruit

The Adafruit Si7021 is a temperature and humidity sensor from Silicon Labs with a PTFE filter for protection against dust and contaminants. It provides ±3% relative humidity accuracy over 0–80% RH and ±0.4 °C temperat...

SKU: SF-SEN-10740 | Brand: SparkFun

An evaluation board for the MLX90614 non-contact infrared thermometer sensor. It pairs the MLX90614 with an ATmega328 running at 3.3 V (8 MHz Arduino bootloader), giving you a ready-to-use IR temperature sensor with s...

SKU: DF-SEN0198 | Brand: DFRobot

What sensor should you use when you need to measure temperature? Most people will think of a DS18B20 temperature sensor first, but this sensor is only capable of measuring temperatures up to 125C. In order to me...

SKU: AF-6403 | Brand: Adafruit

This compact breakout uses Melexis' MLX90632 FIR sensor to read the temperature of a target without making contact. It's handy for checking surfaces that are hot, cold, moving, delicate or awkward to reach with a prob...

SKU: AF-6478 | Brand: Adafruit

This compact breakout combines the STCC4 CO2 sensor with a Sensirion SHT41 temperature and humidity sensor for convenient indoor air monitoring. The STCC4 measures true CO2 using a thermal conductivity method rather t...

SKU: AF-6482 | Brand: Adafruit

Built around Texas Instruments' TMP119, this breakout makes it easy to add extremely accurate temperature monitoring to your project over I2C. It is designed for applications where temperature really matters, includin...