Sensors & Modules

SKU: LB-LR0214-16 | Brand: Little Bird

This compact 12V temperature controller features a 3-digit LED display for setting and monitoring temperature, along with a built-in 10A relay for switching heating or cooling loads. It uses an NTC thermistor probe (i...

SKU: LB-LS2696 | Brand: Little Bird

A waterproof NTC thermistor temperature sensor with a 100cm (1 metre) cable and stainless steel probe. The 10KΩ resistance at 25°C and standard B-constant make it easy to read with an Arduino or other microcontroller ...

SKU: LB-FLAME-LIGHT | Brand: Little Bird

This IR flame sensor module detects flames and infrared light sources in the 760–1,100 nm wavelength range. With a detection angle of approximately 60° and a test range of up to 80 cm (depending on flame size), it pro...

SKU: KI-5647 | Brand: Kitronik

The Prong Soil Moisture Sensor mounts directly onto a BBC micro:bit to monitor soil moisture levels. Two conductive tines are inserted into the soil — any moisture conducts an analogue voltage that the micro:bit reads...

SKU: WS-20167 | Brand: Waveshare

Features At A Glance The Pico-Audio is an audio expansion module designed for Raspberry Pi Pico, which incorporates PCM5101A low power stereo decoder, and uses I2S bus for transmitting audio signal. It supports wi...

SKU: LB-LR0007 | Brand: Little Bird

Flame Detection Sensor Module for use with Arduino Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive60 degree detection sensor   Two outputs mode: AO: analog output, real-time ou...

SKU: AF-1085 | Brand: Adafruit

Add precision analog-to-digital conversion to any microcontroller with the ADS1115 breakout. This 16-bit ADC delivers 860 samples per second over I2C, with four single-ended or two differential input channels and a bu...

SKU: AF-1713 | Brand: Adafruit

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use th...

SKU: SF-SEN-15901 | Brand: SparkFun

This Weather Meter Kit provides the three core sensors for a DIY weather station: an anemometer (wind speed), a wind vane (wind direction), and a rain gauge. All three sensors use passive magnetic reed switches rather...

SKU: AF-1739 | Brand: Adafruit

This large enclosed piezo element (30 mm diameter) converts vibration to voltage and voltage to vibration, making it useful both as a buzzer for generating tones and as a sensor for detecting knocks and impacts. The e...

SKU: AF-1063 | Brand: Adafruit

A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully ass...

SKU: AF-2831 | Brand: Adafruit

This Photo Transistor Light Sensor is a simple sensor that detects ambient light. It's kind of the opposite of an LED - when light hits the little chip inside, it induces current to flow from the long pin...

SKU: SF-SEN-10293 | Brand: SparkFun

A simple piezo element that can be used as both a sensor and a small audio transducer. When flexed or tapped, it generates a voltage that can be read by a microcontroller, making it ideal for knock and vibration detec...

SKU: DF-DFR0052 | Brand: DFRobot

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of vibration.So you can know the...

SKU: DF-SEN0206 | Brand: DFRobot

INTRODUCTION We can divide temperature measurement in to two types: contact and non-contact. Contact measurement can only accurately measure temperature when the testing object and the se...

SKU: DF-DFR0971 | Brand: DFRobot

This 2-Channel I2C DAC module can output a voltage of 0-10V, which is a standard driver in industrial applications. It can be widely used with most 0-10V devices on markets such as light controllers, inverters, valves...

SKU: AF-5463 | Brand: Adafruit

This rubber sheet is made of the same carbon-black impregnated rubber material that our conductive rubber cord uses. Traditionally it would be used for EMF shielding, or conductive gaskets - but it's very fun to play ...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: DF-FIT0510 | Brand: DFRobot

These disposable ECG electrodes are designed for electrocardiogram (ECG) and other biopotential measurements. Each pack contains 12 self-adhesive electrodes made with breathable nonwoven fabric and medical-grade hypoa...

SKU: SF-SEN-09375 | Brand: SparkFun

This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the ...