Sensors & Input

SKU: SF-COM-08236 | Brand: SparkFun

This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down sel...

SKU: SF-BOB-11040 | Brand: SparkFun

The SparkFun LED RingCoder Breakout provides a visual position indicator for rotary encoders. Two 8-bit shift registers drive a circular LED bargraph that displays the virtual position of the encoder as it turns, givi...

SKU: AF-2273 | Brand: Adafruit

This soft potentiometer is an interesting way to add an adjustable resistor / slide potentiometer to your wearable. You can use it to adjust the brightness of an LED, or as a sensor input to your Flora or Gemma. When ...

SKU: DF-SEN0233 | Brand: DFRobot

A multifunction air quality monitor that measures particulate matter (PM2.5), formaldehyde concentration, temperature, and humidity. It uses laser scattering to detect suspended particles in the air, an electrochemica...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: DF-DFR0130-R | Brand: DFRobot

This is a standalone DC voltage meter. It measures 3V-30V with 1% accuracy. Best suited for battery level display. Just apply two wires on the power without any extra circuit or components, it gives the reading st...

SKU: PL-2481 | Brand: Pololu

The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB along with an Omron G5L...

SKU: PL-2454 | Brand: Pololu

The QTR-L-1A reflectance sensor incorporates a right-angle infrared LED and a right-angle phototransistor in an inexpensive, tiny 0.35″ × 0.3″ module that can be mounted almost anywhere and is great for e...

SKU: PL-1483 | Brand: Pololu

This semiconductor gas sensor detects the presence of Carbon Monoxide at concentrations from 10 to 1,000 ppm and combustible gas from 100 to 10,000 ppm. The sensor’s simple analog voltage interface requires ...

SKU: DF-KIT0020 | Brand: DFRobot

An Ultrasonic sensor with scan capability is a must have feature for most robot application. This Ultrasonic scanner kit provides a cost effective way to have such feature for your robot application. This kit is...

SKU: DF-SEN0121 | Brand: DFRobot

This is a steam(water)sensor from DFRobot. This steam sensor can be connected to the Arduino IO Expansion shield directly. The output voltage will increase when the humidity of the sensor surface goes up. Notic...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: DF-DFR0244-G | Brand: DFRobot

A panel-mount LED current meter that measures 0–9.99 A DC with 2% accuracy. The bright green 3-digit LED display is easy to read, and the meter requires no external circuitry — just connect four wires and it gives a r...

SKU: PL-1268 | Brand: Pololu

The Pololu MinIMU-9 v2 is a compact (0.8″ × 0.5″) board that combines ST’s L3GD20 3-axis gyroscope and LSM303DLHC 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore r...

SKU: PL-1265 | Brand: Pololu

This board has been replaced by the newer MinIMU-9 v2 L3GD20 and LSM303DLHC carrier, which offers improved magnetic sensing resolution, a wider acceleration measurement range, and gyro measurements that are more resis...

SKU: SF-SEN-11859 | Brand: SparkFun

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emi...

SKU: DF-SEN0164 | Brand: DFRobot

This adjustable infrared sensor features a high-sensitivity photoreflector to perform distance detection function,ranging from 3cm to 50cm. When the infrared light emitted by the emitter gets reflected on a surface...

SKU: SF-SEN-11769 | Brand: SparkFun

The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measurin...

SKU: SF-SEN-00251 | Brand: SparkFun

36" high temperature Type-K Thermocouple with glass braid insulation.

SKU: SF-BOB-11722 | Brand: SparkFun

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a foo...