Sensors & Input

SKU: LB-LR0109 | Brand: Little Bird

Add Bluetooth functionality to your project with the HC-05 Bluetooth Module. The module is found on a breakout board which provides breadboard-friendly headers for power, ground, TX, RX and enable pins. The breakou...

SKU: DF-DFR0198 | Brand: DFRobot

This is a waterproofed version of the DS18B20 Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PV...

SKU: LB-LR0062 | Brand: Little Bird

This IR sensor can detect obstacles in front of it.  When an object is detected the green indicator light on the board will light up. There is a low-level output signal on the OUT port.It has a detection range of...

SKU: AF-4754 | Brand: Adafruit

The BNO085 from Hillcrest Laboratories is a 9-DOF IMU with built-in sensor fusion — it combines accelerometer, gyroscope and magnetometer data on-chip and delivers ready-to-use orientation, motion detection and activi...

SKU: LB-LS5114 | Brand: Little Bird

The GY-87 is a 10 degrees-of-freedom (10DOF) sensor module that combines three chips on a single compact board: the MPU6050 (3-axis gyroscope + 3-axis accelerometer), HMC5883L (3-axis magnetometer), and BMP180 (barome...

SKU: LB-LR0007 | Brand: Little Bird

Flame Detection Sensor Module for use with Arduino Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive60 degree detection sensor   Two outputs mode: AO: analog output, real-time ou...

SKU: LB-LS0221 | Brand: Little Bird

The CJMCU-226 INA226 is a powerful voltage, current, and power monitoring module designed for high precision in both high-side and low-side sensing applications. With its bi-directional current sensing capability and ...

SKU: DF-SEN0308 | Brand: DFRobot

The Gravity Analogue Waterproof Capacitive Soil Moisture Sensor from DFRobot measures soil moisture using capacitive sensing rather than resistive probes, offering significantly better corrosion resistance and longer ...

SKU: SF-SEN-11050 | Brand: SparkFun

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire i...

SKU: DF-KIT0021 | Brand: DFRobot

A waterproof DS18B20 digital temperature sensor kit with everything you need to connect to an Arduino. The stainless steel probe measures temperatures from -55°C to +125°C over a 1-Wire interface, requiring just one d...

SKU: AF-1713 | Brand: Adafruit

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use th...

SKU: AF-746 | Brand: Adafruit

The Adafruit Ultimate GPS Breakout (Version 3) is a high-performance GPS module built around the MTK3339 chipset. With 66 channels, -165 dBm tracking sensitivity, and up to 10 Hz position updates, it delivers accurate...

SKU: AF-4890 | Brand: Adafruit

Need to measure something with a very slim sensor? This precision 10K thermistor is an inexpensive way to measure temperature in a small gap, or taped to a flat surface, it's only 0.2mm wide!The resistance in 25°C is ...

SKU: SF-SEN-15901 | Brand: SparkFun

This Weather Meter Kit provides the three core sensors for a DIY weather station: an anemometer (wind speed), a wind vane (wind direction), and a rain gauge. All three sensors use passive magnetic reed switches rather...

SKU: DF-SEN0236 | Brand: DFRobot

BME280 is an environmental sensor that integrates onboard temperature sensor, humidity sensor and barometer. The sensor is of high precision, multiple functions, and small size etc. It provides both SPI and I2C in...

SKU: AF-1063 | Brand: Adafruit

A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully ass...

SKU: DF-SEN0244 | Brand: DFRobot

The Gravity Analog TDS Sensor is an Arduino-compatible kit for measuring Total Dissolved Solids (TDS) in water. TDS indicates how many milligrams of soluble solids are dissolved per litre — the higher the value, the l...

SKU: AF-2831 | Brand: Adafruit

This Photo Transistor Light Sensor is a simple sensor that detects ambient light. It's kind of the opposite of an LED - when light hits the little chip inside, it induces current to flow from the long pin...

SKU: SF-SEN-10293 | Brand: SparkFun

A simple piezo element that can be used as both a sensor and a small audio transducer. When flexed or tapped, it generates a voltage that can be read by a microcontroller, making it ideal for knock and vibration detec...

SKU: DF-SEN0257 | Brand: DFRobot

The Gravity Analog Water Pressure Sensor measures water or gas pressure and outputs a linear 0.5–4.5 V analogue signal proportional to the applied pressure (0–1.6 MPa). Using the DFRobot Gravity 3-pin interface, it co...