Motor Drivers and Controllers

SKU: LB-OWL-HBRIDGE | Brand: Little Bird

Using the powerful L298N Dual Motor Driver，this module allows full control of two DC Motors or one stepper-motor. Screw Terminals for easy connections；LEDs show power and output status. Requires six digital inputs....

SKU: EF-EF03406 | Brand: ElecFreaks

Motor:bit is a motor driving board based on micro:bit. It has integrated a TB6612 motor driving chip, which is used to drive two motors with maximun 1.2A DC single channel current. It has also integrated 12 GVS por...

SKU: WS-19767 | Brand: Waveshare

Servo Driver Module For Pico Ideal For Controlling Robotic Arm Or Hexapod Walker Features At A Glance Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Up to 16-Channel servo/PWM outpu...

SKU: AF-2348 | Brand: Adafruit

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed...

SKU: LB-LR0309-57 | Brand: Little Bird

The servo tester and controller can be used as a signal generator for electronic speed controllers.   If you are looking for a low-cost way to get a servo up and running without any programming, you can plug d...

SKU: AF-3297 | Brand: Adafruit

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applic...

SKU: LB-LS1773-12V | Brand: Little Bird

An 8-channel 12V relay module with USB-A interface for computer-based control. Uses the ULN2803 relay driver chip and genuine Songle relays for stable operation. Each relay is rated for 10A switching. Features both a...

SKU: DF-DRI0044 | Brand: DFRobot

The DFRobot 2×1.2A DC Motor Driver is a compact dual-channel motor driver based on the TB6612FNG IC. It requires only four GPIO pins to control two DC motors, using the same control logic as the DFRobot L298N motor dr...

SKU: KS-KS4033 | Brand: Keyestudio

The micro:bit DRV8833 Motor Driver Expansion Board adds dual DC motor control to the BBC micro:bit. Built around the DRV8833CPWP motor driver IC, it can output up to 700 mA per channel with four control modes: clockwi...

SKU: LB-LR0180 | Brand: Little Bird

Including CNC Shield V3.0The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.It has in total 4 channel slots for A4988 stepper motor driver modules for d...

SKU: DF-DRI0043 | Brand: DFRobot

The TB6600 is a professional stepper motor driver for two-phase stepping motors, compatible with Arduino and other microcontrollers that output 5V digital pulse signals. With a wide 9–42VDC power input and up to 4A pe...

SKU: AF-807 | Brand: Adafruit

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally ...

SKU: DF-DFR0144 | Brand: DFRobot

This 4-channel relay shield from DFRobot plugs directly onto an Arduino Uno or compatible board, providing opto-isolated relay switching for controlling high-power devices such as lamps, water pumps, and motors. Each ...

SKU: LB-LR0149 | Brand: Little Bird

The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage w...

SKU: DF-DFR0429 | Brand: DFRobot

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecti...

SKU: LB-LR0051 | Brand: Little Bird

A 4-channel relay module with opto-isolated inputs for safe, reliable switching of high-power loads. Each relay is rated for up to 10A at 250VAC or 30VDC, making it suitable for controlling lights, motors, heaters, an...

SKU: EC-CDP03051C | Brand: Elecrow

The Arduino CNC Shield V3.51 by Protoneer turns an Arduino Uno into a 4-axis CNC controller. Compatible with GRBL 0.9 firmware, it accepts Pololu-style stepper drivers (sold separately) and supports up to 4 stepper mo...

SKU: DF-DFR0502 | Brand: DFRobot

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and...

SKU: AF-2448 | Brand: Adafruit

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel ...

SKU: EC-ACS70028DH | Brand: Elecrow

The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor control...