Environmental (temperature, humidity, air quality)

SKU: LB-LR0214-16 | Brand: Little Bird

This compact 12V temperature controller features a 3-digit LED display for setting and monitoring temperature, along with a built-in 10A relay for switching heating or cooling loads. It uses an NTC thermistor probe (i...

SKU: AF-165 | Brand: Adafruit

The TMP36 is a low-power analog temperature sensor that outputs a voltage proportional to ambient temperature. It operates on 2.7–5.5V and requires no external calibration — simply read the analog voltage and convert ...

SKU: DF-SEN0206 | Brand: DFRobot

INTRODUCTION We can divide temperature measurement in to two types: contact and non-contact. Contact measurement can only accurately measure temperature when the testing object and the se...

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: DF-DFR0067 | Brand: DFRobot

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memo...

SKU: EC-ARS03218S | Brand: Elecrow

The board is designed for beginners in Arduino, with various components available that makes you build more than 10 projects easily. You won’t have to solder or connect anything at all, just plug it in a shield and st...

SKU: DF-DFR0588 | Brand: DFRobot

Gravity: Analog SHT30 Temperature & Humidity Sensor adopts the new generation SHT30 temperature and humidity sensor from Sensirion. Thanks to Sensirion's CMOSens® technology, highly integrated capacitive humidity sens...

SKU: SF-SEN-00250 | Brand: SparkFun

10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. Document...

SKU: EF-EF04079 | Brand: ElecFreaks

Octopus TMP36 Temperature Sensor Brick is a temperature sensor with low voltage and accurate celsius read. It can provide voltage output,which forms a linear relationship with celsius temperature. TMP36 do not need an...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: AF-576 | Brand: Adafruit

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has revers...

SKU: EF-EF05030 | Brand: ElecFreaks

The gas sensor is an essential sensor for environmental detection. The ELECFREAKS PlanetX CO2 Sensor is designed to detect the concentration of CO2 with high sensitivity. The higher the concentration of CO2 is, the sm...

SKU: SF-SEN-17052 | Brand: SparkFun

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher ...

SKU: EF-EF04070 | Brand: ElecFreaks

The Octopus LM35 Analog Temperature Brick is a plug-and-play temperature sensor module based on the TI LM35D precision centigrade temperature sensor. The LM35 outputs a voltage linearly proportional to temperature (10...

SKU: AF-4686 | Brand: Adafruit

The Adafruit TMP235 is a plug-and-play analog temperature sensor with a 3-pin JST PH (STEMMA) connector. Unlike I2C sensors, this one outputs a simple analog voltage proportional to temperature — just connect it to an...

SKU: DF-SEN0256 | Brand: DFRobot

The DFRobot TS01 is a non-contact infrared temperature sensor that measures surface temperature via infrared radiation. The all-metal IP65 housing provides protection against impact, water, and dust, making it suitabl...

SKU: DF-SEN0264 | Brand: DFRobot

DFRobot TS01 IR temperature sensor is a non-contact thermal sensor, which can be used to measure the infrared intensity of the object so as to calculate its surface temperature without touching. The built-in temperatu...

SKU: DF-DFR0280 | Brand: DFRobot

Sharp GP2Y1010AU Dust Sensor requires some wiring on the breadboard and a list of components to make it Arduino compatible. This has turned down several people due to the thin wires of the sharp sensor making it ...

SKU: AF-249 | Brand: Adafruit

This pack includes everything you need to build a light and temperature data logger with an Arduino. The Adafruit data logger shield records sensor readings to an SD card with real-time timestamps, while the included ...