Circuitry & IOT

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-TOL-12966 | Brand: SparkFun

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: DF-DFR1075 | Brand: DFRobot

The FireBeetle 2 ESP32-C6 is a low-power IoT development board built around a 160MHz RISC-V single-core processor. It supports Wi-Fi 6 (802.11ax), Bluetooth 5, Zigbee 3.0, Thread 1.3, and the Matter smart home standar...

SKU: EF-EF02054 | Brand: ElecFreaks

DescriptionWukong 2040 is a multifunctional Breakout Board designed for Raspberry Pi Pico. In terms of functions, it is equipped with a buzzer, A\B buttons, rainbow lights, motor interface, reset button, etc., to meet...

SKU: DF-DFR0896 | Brand: DFRobot

The ESP32-S3-WROOM-1-N4 is a powerful Wi-Fi and Bluetooth LE MCU module built around the ESP32-S3 SoC. Featuring a dual-core Xtensa LX7 processor running at up to 240MHz, 4MB SPI flash, and hardware acceleration for n...

SKU: AF-5348 | Brand: Adafruit

The Adafruit QT Py ESP32-S2 with uFL Antenna Port is the extended-range version of the QT Py ESP32-S2. Instead of an on-board antenna, it features a uFL connector so you can attach any 2.4 GHz Wi-Fi antenna for signif...

SKU: DF-DFR0807 | Brand: DFRobot

ESP32-C3-DevKitM-1 is an entry-level development board based on ESP32-C3-MINI-1, a module named for its small size. This board integrates complete Wi-Fi and Bluetooth LE functions. Most of the I/O pins on the ESP32-C3...

SKU: EC-SEL71220A | Brand: Elecrow

A current sensing module based on the Allegro ACS712 Hall effect sensor, capable of accurately measuring both AC and DC current up to ±20 A. The module outputs a proportional analogue voltage that can be read directly...

SKU: EC-SPM32100S | Brand: Elecrow

This Moisture Sensor can be used to detect the moisture of soil or your pet plant's water level, let the plants in your garden reach out for human help. With the Octopus Electronic Bricks interface can very easy to us...

SKU: EC-SEA0001T | Brand: Elecrow

The Crowtail Starter Kit for Arduino is a beginner-friendly electronics kit built around the Crowduino Uno-SD board and the Crowtail modular connector system. With 22 plug-and-play modules and over 20 guided tutorials...

SKU: EC-ACS70028DH | Brand: Elecrow

The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor control...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: DF-FIT0610 | Brand: DFRobot

This enclosed battery holder takes 3× AA batteries in series, providing approximately 4.5V from alkaline cells or 3.6V from NiMH/NiCd rechargeables. It features a built-in on/off switch and a sliding, removable cover ...

SKU: AF-4193 | Brand: Adafruit

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and p...

SKU: EF-EF04027 | Brand: ElecFreaks

Octopus Soil Moisture Sensor Brick can read the amount of moisture present in the soil surrounding it. It's a low tech sensor, but ideal for monitoring an urban garden, or your pet plant's water level. This is a mu...

SKU: AF-3648 | Brand: Adafruit

The Adafruit PT1000 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter, configured for PT1000 platinum resistance temperature detectors. It reads 2-, 3-, or 4-wire...