Circuitry & IOT

SKU: SF-SEN-13322 | Brand: SparkFun

The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probe...

SKU: DF-ROB0117 | Brand: DFRobot

The Cherokey 4WD Basic Arduino Robot Kit is a perfect wheeled robot platform to build your own robot and to get started with Arduino Robot. With just a few simple steps of assembling the hardware and tuning the...

SKU: DF-DFR0359 | Brand: DFRobot

INTRODUCTION eClip is an innovative programming/testing tool specially designed for Makers. It solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spa...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: DF-FIT0423 | Brand: DFRobot

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors,...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...

SKU: AF-3391 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: SF-PRT-09390 | Brand: SparkFun

This is a SparkFun exclusive! These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" h...

SKU: AF-3588 | Brand: Adafruit

The Adafruit MetroX Classic Kit is a comprehensive experimentation kit with over 20 guided circuits and projects to explore microcontroller basics. Built around the Adafruit Metro 328 (Arduino UNO-compatible), this ki...

SKU: DF-KIT0194 | Brand: DFRobot

This expansion ecosystem transforms the UNIHIKER M10 single-board computer into a fully functional AIoT development station. By leveraging the modular DFRobot Gravity interface, the kit allows for the seamless integr...

SKU: AF-6420 | Brand: Adafruit

The Adafruit SPA06-003 is an affordable barometric pressure and temperature sensor from Goertek, ideal for basic environmental sensing and DIY quadcopter builds. It measures 300–1100 hPa (approximately −500 to +9000 m...

SKU: SF-WRL-28434 | Brand: SparkFun

The SparkFun IoT RedBoard combines the powerful ESP32-D0WDQ6 microcontroller with MicroPython pre-installed, letting you start coding IoT projects right out of the box. No need for complex toolchains – just connect vi...

SKU: KS-FB0001 | Brand: Keyestudio

 The FoxBit is a versatile development board built around the powerful ESP32-D0WDQ6 dual-core microcontroller, designed for education, makers, and electronics enthusiasts. Ideal for IoT, STEAM education, smart c...