Breakouts

This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch or o...

Add motion, direction and orientation sensing to your project with this all-in-one 9-DOF sensor from Adafruit. The LSM9DS0 from ST Micro combines a...

Unlike most of the other temperature sensors we have, this breakout has a really cool IR sensor from TI that can measure the temperature of an o...

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: wh...

Now mounted on a breakout board, the MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa...

This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionali...

The Adafruit Si5351A Clock Generator Breakout lets you generate precise, arbitrary clock frequencies from 8 kHz to over 150 MHz using a simple I2C ...

Overview DRV8838 Single Brushed DC Motor Driver Carrier, bottom view with dimensions. TI SN754410 (16-pin DIP) next to the #2135 DRV8835 c...

This is a breakout board for Honeywell’s HIH-4030 humidity sensor. The HIH-4030 measures relative humidity (%RH) and delivers it as an analog outpu...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are...

This is a breakout board for the RN-131g WiFly GSX module, an ultra-low power 802.11b/g transceiver. This board breaks out all pins of the RN-13...

A multi-interface expansion shield for Arduino that consolidates SPI, I2C, micro-SD, SD card, and TLC5940 LED controller connections onto a single ...

At sometime or another you may run out of pins on your Arduino board and need to extend it with shift registers.  With this shift out module which ...

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflect...

The Adafruit 1.44" Colour TFT LCD Display Breakout is a compact 128×128 pixel screen driven by the ST7735R controller over 4-wire SPI. Unlike older...

The 2.8" TFT LCD Breakout Board features a bright, full-colour display with a capacitive single-touch touchscreen and an onboard MicroSD card socke...

A 40-pin FPC extension board with an included 200mm flexible flat cable. Adds approximately 22cm of reach (20cm cable plus 2cm board) to devices us...

DFRobot FireBeetle is a low-power consumption micro-controller intentionally designed for Internet of Things (IoT). This series micro-control...

Add heat-vision to your project with the Adafruit AMG8833 Grid-EYE Breakout. This sensor from Panasonic contains an 8×8 array of infrared thermal s...

DFRobot FireBeetle is a low-power consumption micro-controller intentionally designed for Internet of Things (IoT). This series micro-controller...

This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B c...

This is a breakout board for our non-isolated, 6A DC-to-DC Converter Module. The module can convert any DC voltage between 4.5-14VDC to a selectabl...

The Pimoroni Pico HAT Hacker gives you full access to all 40 GPIO pins on your Raspberry Pi, broken out at the top of the board. At just 0.8mm thic...

The Gravity IIC to Dual UART Module converts a single I2C connection into two independent hardware serial ports. Each sub-UART has its own 256-byte...