Breakouts

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering p...

The SparkFun MAG3110 breakout board provides easy access to Freescale's MAG3110 triple-axis digital magnetometer. When paired with a 3-axis acceler...

A prototyping shield for the Raspberry Pi that stacks directly onto the GPIO header using dual headers on the underside. The board features a large...

The Adafruit HTU21D-F is an accurate I²C digital temperature and humidity sensor breakout board. With typical humidity accuracy of ±2% (optimised f...

This is a simple breakout for the ADXL345 accelerometer and the ITG-3200 MEMS gyro. With this board, you get a full 6 degrees of freedom. The senso...

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex tr...

INTRODUCTION The Cookie I/O expansion shield is designed for beginners to electronics. The shield is directly compatible...

This 1.27mm pitch, 2x5 male SMT Box Header is the same one used on our SWD Cable Breakout Board. The header alone is great if you want to inc...

This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version’s headers...

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping US...

The SparkFun Bluetooth Mate Silver is a Bluetooth Classic serial modem based on the Roving Networks RN-42 module. It acts as a wireless serial (RX/...

This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting piezoe...

The Adafruit FONA Mini Cellular GSM Breakout (SMA Version) is a compact 1.75 × 1.25-inch cellular module that adds voice, text, SMS, and GPRS data ...

The Adafruit FONA Mini Cellular GSM Breakout (uFL Version) is a compact 1.75 × 1.25-inch cellular module that adds voice, text, SMS, and GPRS data ...

Interested in learning how Bluetooth Low Energy works down to the packet level? Debugging your own BLE hardware, and trying to spot where someth...

The Adafruit Precision NXP 9-DOF Breakout combines the FXOS8700 3-axis accelerometer/magnetometer and the FXAS21002 3-axis gyroscope on a single bo...

The Adafruit Stereo FM Transmitter Breakout is based on the Si4713, a high-quality stereo FM transmitter chip with RDS/RBDS support. Feed line-leve...

The SparkFun FTDI Basic Breakout provides USB-to-serial conversion using the FTDI FT232RL IC, operating at 3.3V logic levels. Its 6-pin header matc...

A compact breakout board featuring the ADMP401 MEMS microphone with bottom-ported input, allowing the microphone to sit flush against your project'...

Note: This TFT has been discontinued. The replacement 2.2″ TFT (ILI9340) uses a different controller and wiring, so it is not a drop-in replacemen...

The Joystick Shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets...

The Adafruit Pi Cobbler Plus Kit breaks out all 40 GPIO pins from a Raspberry Pi B+, A+, Pi 2, or Pi 3 onto a solderless breadboard. Connect the in...

The Adafruit Pi T-Cobbler Plus Kit breaks out all 40 GPIO pins from a Raspberry Pi onto a solderless breadboard in a wide T-shaped layout. The T-sh...