All Products
Showing 61-73 of 73 products · 13 unavailable products hidden
Adafruit Floppy FeatherWing with 34-Pin IDC Connector
The Adafruit Floppy FeatherWing lets you read and write 3.5-inch or 5.25-inch floppy disks using a Feather microcontroller. It connects to standard 34-pin IDC floppy drives and includes built-in level shifting between 3.3 V Feather logic and the 5 V signals that floppy drives require. Floppy dri...
SparkFun USB Mini-B Breakout
A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...
USB Micro-B Breakout Board
·
This breakout board gives you easy access to all 5 pins of a USB Micro-B connector via standard 0.1" header pins. It's a simple way to add USB 5V power to a project, interface with a USB-capable microcontroller, or prototype custom USB connections on a breadboard. The board uses a micro-AB conne...
Adafruit Itsy Bitsy 32u4 - 5V 16MHz
·
The Adafruit Itsy Bitsy 32u4 5V packs the power of an Arduino Leonardo into a tiny 1.4" × 0.7" board. Built on the ATmega32u4 running at 5V and 16 MHz — the same speed and voltage as an Arduino Uno — it's perfect for shrinking finished prototypes into compact final builds. With native USB, the I...
Adafruit Trinket - 5V
·
The Adafruit Trinket 5V is a tiny microcontroller board built around the Atmel ATtiny85 processor. At just 27mm × 15mm, it's small enough to fit into virtually any project and affordable enough to dedicate to a single build. Program it via the Arduino IDE over the Micro-USB connector — no separat...
USB to TTL Serial Cable (5V VCC)
This is a USB to TTL Serial Cable which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this cable are configured to operate at 3.3V specifically with a Raspberry Pi with each serial pin broken apart. Thanks to its separated pins, this cable is a perfect candidate...
Pinout Motor/ Servor Shield for BBC Micro: bit
This motor/ servo shield is for Micro: bit, it provides a simple way to add motor driving capability to a micro: bit. The shield can drive 2 motors, 2 servos, and allow the motors to be driven with forward, reverse, stop control. It’s easy to add the motor to the shield, and there is an integrate...
Gemma Starter Pack
·
Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...
Raspberry Pi 400 Personal Computer (Unit Only)
The Raspberry Pi 400 is a complete Raspberry Pi 4-based personal computer, integrated into a keyboard. By incorporating the board into a keyboard, it removes the need for a case and other accessories normally needed to run a Raspberry and creates a more clean configuration. It makes for the perfe...
Adafruit KB2040 - RP2040 Kee Boar Driver
·
The Adafruit KB2040 is an RP2040-powered board designed specifically for mechanical keyboard builds, in the Arduino Pro Micro form factor. With castellated pads, USB-C, 8 MB of Flash, and a STEMMA QT / Qwiic connector, it's a drop-in replacement for Pro Micro boards with significantly more power ...
4.7" E-ink Screen for ESP32
This 4.7" e-ink display board integrates an ESP32-WROVER-E module (ESP32-D0WDQ6 V3) with 16MB Flash and 8MB PSRAM, providing a complete development platform for low-power e-ink projects. The display supports 16 grayscale levels and partial refresh for faster screen updates. The board features 3 ...
Digi-Key Hackbox - Clue and PyLeap
A curated electronics kit built around the Adafruit CLUE board and PyLeap — Adafruit's app for wirelessly transferring code and assets from the Learn system directly to your device. No complicated setup or USB cable needed for programming once you're connected via Bluetooth. The CLUE board packs...
ESP32-S3 AMOLED Touch Watch Dev Board – Dual-Core, 410x502, Dual Mics
·
Unleash Your Creativity with the ESP32-S3 2.06inch AMOLED Touch Watch Development Board Take your wearable tech designs to the next level with the powerful and versatile ESP32-S3 2.06inch AMOLED Touch Watch Development Board. This sleek, cutting-edge development tool is crafted for tinkerers, dev...
