All Products

SKU: SF-PRT-10592

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the battery and the PCB pad underneath is connected to the negative side.

SKU: AF-2272 · MPN: 2272

This battery holder is designed to clip and hold Panasonic camcorder lithium-ion battery packs, providing a convenient high-capacity power source for custom projects. Simply snap your battery in, and use your existing charger to top it up when needed. Compatible Batteries Panasonic CGR-D28 – 7...

SKU: DF-DFR0208

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo battery at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will wo...

SKU: AF-4712 · MPN: 4712

The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...

SKU: SF-DEV-21326 · MPN: DEV-21326

This compact MicroMod processor board adds an STM32F405 to a compatible MicroMod Carrier Board, giving your project an ARM® Cortex®-M4 32-bit RISC core in a small, swappable M.2 module.The bevelled edge connector keys into the MicroMod M.2 socket and is secured with the screw supplied with MicroM...

SKU: SF-PRT-13113

This is a PCB mount clip to hold a 18650 Lithium Ion Cell battery. Each battery holder is sold in single units, you’ll need two for each battery. These work great for larger, high capacity applications where a drop-in rechargable cell is needed. These little guys are low cost and easy to use! No...

SKU: AF-2345 · MPN: 2345

The Adafruit RGB Matrix HAT + RTC makes it easy to drive HUB75-type RGB LED matrices from your Raspberry Pi. This HAT plugs onto any Pi with a 40-pin GPIO header and includes a DS1307 real-time clock, so your Pi can keep accurate time even after reboots or power loss — perfect for clock and time-...

SKU: AF-653 · MPN: 653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: DF-DFR0999

The Gravity SCI DAQ Module is a multi-functional data acquisition module with a built-in 1.3-inch OLED screen for real-time sensor readings. It supports over 20 common sensor types including temperature, humidity, and barometric pressure — with automatic sensor recognition and a standardised I2C ...

SKU: AF-5980 · MPN: ADA5980

The Feather RP2040 Adalogger combines the RP2040 dual-core processor with a MicroSD card holder for data logging and file storage. It features 8 MB SPI flash, 264 KB SRAM, USB Type C, STEMMA QT connector, and built-in LiPo battery charging — ready for portable data recording projects with Arduino...

SKU: SF-PRT-12899

A single-cell 18650 battery holder with wire leads for easy integration into projects. Drop in an 18650 lithium-ion cell and connect the bare wire leads to your circuit — no soldering to the battery required. Two 6" (150 mm) cables exit from opposite ends of the holder, terminated with bare wire...

SKU: SF-PRT-11892

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The metal housing connects to the positive (+) side of the battery and the PCB pad underneath is connecte...