All Products
Showing 10441-10460 of 11441 products
Tamiya 70171 3mm Threaded Shaft Set
The Tamiya 70171 3mm Threaded Shaft Set includes two fully-threaded 3 × 150mm shafts with ball joints and connectors for building control rods with three-dimensional movement. The shafts can be cut to any desired length, making them versatile for linkages, pulley mounting, and mechanical assembli...
Tamiya Plug with 10cm Leads, Female
This style of high-current connector is commonly used with the 7.2V sub-C battery packs that power many RC cars. The connector is keyed so that power cannot be reversed, and a latch secures the connection so that it will not become disconnected. This female Tamiya connector has 10cm 14-AWG leads...
Tamiya Plug with 10cm Leads, Male
A male Tamiya-style high-current connector with two pre-crimped 10cm 14-AWG silicone-insulated leads. This keyed connector is commonly used with 7.2V RC battery packs and features a latch to prevent accidental disconnection. The leads extend 9cm past the housing with stripped, tinned terminations...
Taoglas FXP895 Flexible PCB ISM/LoRa Antenna - 860-928MHz
·
The Taoglas FXP895 is a compact flexible PCB antenna for ISM and LoRa applications, designed to fit into small connected devices where space is tight.Its wideband 860 to 928MHz coverage suits regional ISM/LoRa frequency bands, helping one antenna design support multiple markets. The flexible PCB ...
Taoglas Steedan MA350 5-in-1 Magnetic Mount Antenna
·
The Taoglas Steedan MA350 is a low-profile 5-in-1 combination antenna designed for vehicle roofs, outdoor buildings and heavy equipment where drilling through a roof or metal panel is not feasible. Its magnetic base mounts to steel surfaces using ultra-strong neodymium magnets, while a soft foam ...
Tattu 1050mAh
Tattu 3S 11.1V 1050mAh 75C LiPo Battery (XT-60)The Tattu 3S 1050mAh LiPo battery is a compact powerhouse designed with Micro UAVs and high-performance RC applications in mind. With a discharge rate of 75C (and a burst rate of 150C), this pack delivers serious punch while keeping the weight down—j...
TB6600 arduino Stepper Motor Driver
The TB6600 is a professional stepper motor driver for two-phase stepping motors, compatible with Arduino and other microcontrollers that output 5V digital pulse signals. With a wide 9–42VDC power input and up to 4A peak current output, it handles most 42-type and 57-type stepper motors. Features...
TB6612FNG Dual Motor Driver Carrier
This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectional DC motors or one bipolar stepper motor. A recommended motor voltage of 4.5 V to 13.5 V and peak current output of 3 A per channel (1 A continuous) ma...
TC01 Non-contact 16x4 Pixel Infrared Temperature Sensor
The TC01 is a non-contact infrared temperature sensor with a 16×4 pixel array, producing a 64-pixel thermal image. Housed in a waterproof, dustproof metal enclosure (IP65), it communicates via RS485 using the standard Modbus-RTU industrial protocol for easy integration with industrial controllers...
TCA9548A I2C Multiplexer
·
The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels on command. Simply write a single byte to the multiplexer's I2C address (defau...
T-Camera ESP32 WROVER PSRAM Camera Module
The T-Camera is a powerful and compact development board designed for camera-based IoT applications. Powered by an ESP32 dual-core processor, it combines Wi-Fi, Bluetooth, and camera functionality, making it ideal for face recognition, security monitoring, and other smart camera projects. With it...
T-Connector For Silicone Tubing - 5 Pack
·
These T-shaped barbed connectors allow you to split or combine silicone tubing runs into three-way junctions. Each port has an outer diameter of approximately 4 mm, designed to fit snugly with 3 mm ID silicone tubing for a secure seal. Key Features T-Junction Design – Three-way barbed connecto...
TCR2EF33 Fixed 3.3V 200mA Voltage Regulator
·
This compact CMOS regulator provides a fixed 3.3V single output for low-current electronics projects and embedded hardware. It is rated for up to 200mA output current and is intended for surface-mount designs.The regulator includes an on/off control input, making it suitable for circuits that nee...
TCS3200 RGB Color Sensor For Arduino
An RGB colour sensor breakout board based on the TAOS TCS3200 chip, with four built-in white LEDs for illumination. The TCS3200 can detect and measure a wide range of visible colours by converting light intensity to a frequency output that can be read directly by a microcontroller. The sensor co...
TCS3430/TCS34303 Ambient Tri-Stimulus Colour Sensor
·
This breakout brings ambient light tri-stimulus colour sensing to your project using CIE XYZ plus an IR channel, rather than the more common RGB-style approach. It is designed for applications where you want access to the raw sensor count data so you can match and calibrate it to your own colour ...
TCS34725 RGB Color Sensor For Arduino
The TCS34725 is an I2C RGB colour sensor that detects the red, green, and blue components of light in its environment and returns digital colour values. With high sensitivity, a wide dynamic range, and a built-in IR blocking filter, it delivers accurate colour readings under varied lighting condi...
Teaching With Edison
A webinar designed to help educators incorporate the Edison Robot into the Digital Technologies curriculum. Learn practical strategies for introducing robotics and coding in the classroom using Edison's accessible, student-friendly platform. This session covers an introduction to the Edison Robo...
Teaching With Grove Zero
Learn how to incorporate Grove Zero in your Digital Technologies Curriculum.In this webinar, you will be introduced to the Grove Zero and shown examples on how they can be implemented in the classroom.
Teaching With Makeblock Neuron
Learn how to incorporate Makeblock Neuron in your Digital Technologies Curriculum.In this webinar, you will be introduced to the Makeblock Neuron and shown examples on how they can be implemented in the classroom.
Teaching With Makey Makey
Learn how to incorporate the Makey Makey in your Digital Technologies Curriculum.In this webinar, you will be introduced to the Makey Makey board and shown examples on how it can be implemented in the classroom.
