All Products

SKU: SF-BOB-13021

This is the SparkFun RJ45 MagJack Breakout, a simple board that will provide you with a way to put an ethernet port into your breadboard. The SparkFun RJ45 MagJack Breakout is the same one found in our very own mbed Starter Kit and breaks out each pin from the ethernet jack. This rev of the br...

SKU: SF-PRT-29920 · MPN: PRT-29920

This adapter makes it straightforward to add a wired Ethernet connection to a Teensy 4.1. It brings the functionality of the Ethernet Kit for Teensy 4.1 onto a single board, helping you get a network-capable setup together with less assembly.The tricky parts are already taken care of, with the RJ...

SKU: SF-BOB-00716

RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: WS-16595

This Raspberry Pi hub HAT provides more USB capability to your Pi, plus a RJ45 Ethernet port, which is great when you need a stable wired Ethernet connection. It can work with various versions of the Pi, and the size of the board is designed to perfectly fit the Zero / Zero W / Zero WH. Features...

SKU: SF-BOB-13906

The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eig...

SKU: DF-FIT0849

This Ethernet RJ45 Female Plug to 8-Pin Terminal Block provides a solder-free way to break out an RJ45 Ethernet connection to individual screw terminals. The standard RJ45 port features a metal shielding layer for electromagnetic interference protection, while the detachable terminal block allows...

SKU: SF-BOB-13878

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s nest of wires. The Load Sensor Combinator was created to combine the 12 wires foun...

SKU: SF-SEN-15335

The SparkFun 9DoF IMU Breakout brings InvenSense's ICM-20948 9-axis motion tracking sensor to a Qwiic-enabled breakout board with an on-board logic level shifter and broken-out GPIO pins. The ICM-20948 is an extremely low-power sensor supporting both I2C and SPI communication, suited for wearable...

SKU: DF-FIT0853

This M12 to RJ45 Ethernet adapter uses M12 female 4 pin D coded with IP67 waterproof rating, which is impervious to dust and short-term soaking, safe and reliable to use. There are metal shielding layers on the RJ45 port for fixing interface and preventing external electromagnetic interference, w...

SKU: DF-FIT0854

This M12 to RJ45 Ethernet adapter uses M12 male 4 pin D coded with IP67 waterproof rating, which is impervious to dust and short-term soaking, safe and reliable to use. There are metal shielding layers on the RJ45 port for fixing interface and preventing external electromagnetic interference, whi...

SKU: SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: DF-FIT1005 · MPN: FIT1005

The M.2 2.5G Network Card adds high-speed Ethernet connectivity to devices with an M.2 B+M Key slot. Powered by the Intel I225-V chipset, it supports adaptive data rates up to 2500 Mbps and is compatible with LattePanda Alpha, LattePanda 3 Delta, LattePanda Sigma, and other M.2-equipped single-bo...

SKU: SF-PRT-00643

These are simple through-hole RJ45 sockets with PCB mounting posts. These 8-pin connectors are commonly used in conjunction with Cat5, Cat5e, and Cat6 Ethernet cables. Because Ethernet cable is so ubiquitous, these are awesome for projects where you need to string a lot of modules together ove...

SKU: SF-BOB-11771

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA acc...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...

SKU: SF-BOB-13282

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addres...

SKU: DF-FIT0858

This DB15 Male to RJ45 Female Adapter can be used to handle data communication between VGA interface devices with one RJ45 network cable, or as an extender to extend VGA signal to about 20m.Two modules are required for video transmission. It enables to extend signal to 20m with CAT5/6 network cab...

SKU: DF-FIT0851

This DIN Rail RJ45 Terminal Block Adapter-Vertical, perfect for simplifying complex wiring, consists of an RJ45 Ethernet jack and an eight-port terminal. You can connect an RJ45 Ethernet to PCB which can be DIN rail-mounted, easy to use. Then, all 8 wires are broken out into terminal bloc...

SKU: DF-FIT0848 · MPN: FIT0848

This adaptor connects a standard RJ45 Ethernet plug format to an 8-pin terminal block, making it handy for wiring network-related projects without soldering.The RJ45 side includes metal shielding layers to help fix the interface securely and reduce external electromagnetic interference for a more...