All Products

SKU: AF-1831

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poi...

SKU: AF-5281

An Alpha 5K linear potentiometer with right-angle PC mount pins spaced at 0.2" — perfect for plugging directly into a breadboard or perfboard during prototyping. When you're ready for a permanent build, mount it to a panel using the included washer and hex nut. Key Features 5K Ohm Linear Taper...

SKU: AF-5611

The Adafruit PCF8575 GPIO Expander Breakout is an affordable 16-channel I2C GPIO expander that doubles your available digital I/O over a simple two-wire connection. Add extra buttons, LEDs, relays, or other digital peripherals to any microcontroller without using up precious GPIO pins. Like its ...

SKU: SF-COM-14624

A panel-mount rotary potentiometer with a 100 kΩ logarithmic taper. Turn the knob and the resistance changes smoothly — ideal for volume controls and other audio applications where a logarithmic response matches human perception. Connect VCC to one outer pin, GND to the other, and the centre pin...

SKU: SF-SPX-21226 · MPN: SPX-21226

This handy kit gives you a simple way to compare and tune the brightness of your own LEDs, helping you avoid a project full of mismatched indicator lights. It was originally designed for side-by-side LED testing and is especially useful when choosing resistor values or learning how brightness cha...

SKU: AF-5545

The Adafruit PCF8574 GPIO Expander Breakout is an affordable 8-channel I2C GPIO expander that adds extra digital I/O to any microcontroller project. Simply connect over I2C and control up to 8 additional pins for buttons, LEDs, or other digital peripherals — no extra GPIO-rich board required. Th...

SKU: AF-3393

A dual-ganged 10K linear potentiometer with a built-in on/off switch — two components in one convenient panel-mount package. The dual 10 kΩ linear-taper pots share a grippy shaft that turns smoothly without shifting on its own, and the on/off switch activates at the beginning of the shaft's rotat...

SKU: AF-4133

A compact 10K ohm linear potentiometer with a built-in knurled plastic knob — no separate knob needed. The 0.1" pin spacing plugs directly into a standard breadboard, making it perfect for prototyping and quick adjustments. Larger than a trim-pot but smaller than a full-size panel-mount potentio...

SKU: EF-EF04061

A linear sliding potentiometer module from the ElecFreaks Octopus series. Provides an analogue voltage output proportional to the slider position, making it useful as a variable input for controlling volume, brightness, speed, or any other parameter in your project. Features a standard 3-pin con...

SKU: AF-3391

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can p...

SKU: EC-ACA30002A

The Component Kit for Arduino E3 is a starter-friendly assortment of essential electronic components for use with any Arduino-compatible board. It includes a broad range of resistor values, LEDs in four colours, tactile switches with button caps, potentiometers, and pin headers — everything you n...

SKU: AF-4464

The Adafruit ICM-20649 breakout features a wide-range 6-DoF IMU capable of measuring up to ±30g acceleration and ±4000°/s gyroscope rotation — roughly double the range of standard IMUs. When typical ±16g accelerometers and ±2000°/s gyros aren't enough, this sensor delivers the extended measuremen...

SKU: AF-3246

A neat little breakout board designed for mounting a PSP-style mini thumbstick to your project. The board features panel-mount friendly hole placement and dual-sided headers for mechanical stability when connected to a breadboard or perfboard. Since the thumbstick is analog, you'll need two anal...

SKU: AF-395

An 8-channel bidirectional logic level converter breakout based on the TXB0108 chip. This converter automatically detects signal direction, eliminating the need for direction control pins. It shifts between virtually any two voltage levels, making it ideal for connecting 3.3V and 5V devices. The...

SKU: AF-562

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poin...

SKU: SF-COM-14622

An adjustable potentiometer can open up many interesting user interfaces. With this rotary potentiometer just turn the dial and the resistance changes. This potentiometer has a ¼" metal knurled shaft diameter, solder lug terminals, no detents, and has a 100K linear taper. Connect VCC to an outer...

SKU: AF-2046

Oh say can you see By the knob's early light... Sorry - we thought that was clever.  And while it wasn't really, this potentiometer knob definitely is.  It's a 'soft touch' T18 knob that works great with our Panel Mount 10K, Panel Mount 1K, and Panel Mount 100K potentiomet...

SKU: AF-2047

A soft-touch T18 potentiometer knob in white with a rubbery grip for comfortable, precise adjustment. Features a white indicator line on the outside for clear position visibility. Designed to press-fit directly onto T18 splined potentiometer shafts for a secure connection. Compatible with standa...

SKU: AF-5631 · MPN: ADA5631

This break-apart panel gives you 12 PB86 step switch breakout PCBs, making these colourful sequencer-style switches much easier to use in a breadboard, perfboard or DIY synth build.The original switches are not breadboard or perfboard friendly, so these assembled breakouts save you from hand-wiri...

SKU: DF-DFR0520

Digital potentiometer is also called "Digital Pot" in short. It is a kind of mixed signal IC, which is able to dynamically change the internal resistors through MCU like Arduino. It can be applied to applications such as LED DC dimming, linear stable voltage source, oscillator, low pass filter o...