All Products

SKU: SF-DEV-08777

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient...

SKU: AF-249

This pack includes everything you need to build a light and temperature data logger with an Arduino. The Adafruit data logger shield records sensor readings to an SD card with real-time timestamps, while the included photocell and TMP36 temperature sensor provide light level and temperature measu...

SKU: DF-SEN0335

Build up a simple environmental monitor station with this multi-function environment sensor! Based on the combination of CCS811+BME280 chip, this module features high accuracy, I2C interface, and fast Measurement. The BME280 can provide temperature and humidity compensation for CCS811 to impro...

SKU: DF-KIT0021

A waterproof DS18B20 digital temperature sensor kit with everything you need to connect to an Arduino. The stainless steel probe measures temperatures from -55°C to +125°C over a 1-Wire interface, requiring just one digital pin for communication. Multiple sensors can share the same data pin thank...

SKU: M5-U070

The M5StickC Yun HAT is a cloud-shaped multi-sensor environmental monitoring accessory designed to mount on the M5StickC via the top socket. It integrates a temperature and humidity sensor (SHT20), barometric pressure sensor (BMP280), a photoresistor for ambient light detection, and 14 SK6812 RGB...

SKU: LB-LR-DIGI-TEMP-3M-UA

The Little Bird 1-Wire Digital Temperature Sensor for Raspberry Pi — a plug-and-play solution for environment sensing, data logging, and IoT applications. Simply plug it onto the Raspberry Pi GPIO header — no breadboard, jumper wires, or additional components needed. This is the unassembled vers...

SKU: LB-LR-DIGI-TEMP-3M-A

The Little Bird 1-Wire Digital Temperature Sensor for Raspberry Pi — a plug-and-play solution for environment sensing, data logging, and IoT applications. Simply plug it onto the Raspberry Pi GPIO header — no breadboard, jumper wires, or additional components needed. This is the assembled versio...

SKU: LB-24-TEMP

A pre-wired DS18B20 digital temperature sensor on a breakout module with three labelled pins for easy connection. The DS18B20 uses the 1-Wire protocol, requiring only a single data line to communicate temperature readings to a microcontroller such as a Raspberry Pi, Arduino, or micro:bit. Key Fe...

SKU: SF-SEN-00245

The DS18B20 is a digital temperature sensor from Maxim (now Analog Devices) that communicates over a 1-Wire bus. It reports temperature in degrees Celsius with 9 to 12-bit configurable resolution. Each sensor has a unique 64-bit serial number, allowing multiple sensors to share a single data line...

SKU: AF-165

The TMP36 is a low-power analog temperature sensor that outputs a voltage proportional to ambient temperature. It operates on 2.7–5.5V and requires no external calibration — simply read the analog voltage and convert to temperature. Key Features Analog Voltage Output – Proportional to temperat...

SKU: EC-SEM02001S

Japan's Hokuriku resistive humidity sensor production as a Temperature & Humidity sensor.Application Idea Test and testing equipment; Automatic control; Weather station; Humidity regulator; Features Measure the relative temperature and humidity sensor (humidity range 18% - 98% temperature range -...

SKU: EF-EF04070

The Octopus LM35 Analog Temperature Brick is a plug-and-play temperature sensor module based on the TI LM35D precision centigrade temperature sensor. The LM35 outputs a voltage linearly proportional to temperature (10 mV/°C), making it easy to read with any microcontroller's analog input — no cal...

SKU: SF-DEV-11262

The ProtoSnap series is a new way to prototype your project without a breadboard. Everything is wired together on a single board, which makes it easy to explore the possibilities of the components before snapping them apart and building them into your project. The ProtoSnap LilyPad Development...

SKU: AF-3846

This is a pre-wired and waterproofed version of the DS18B20 sensor made with a PTFE wire cable. Handy for when you need to measure something far away, or in wet conditions. This sensor is a little more expensive than the other waterproof version we have with a PVC cable because this one can be...

SKU: DF-SER0059

A miniature serial bus servo from DFRobot that delivers 2.3 kg·cm of stall torque at 6 V, controllable via TTL serial communication. Up to 253 servos can be daisy-chained in series, each assigned a unique ID for individual or synchronised control at baud rates up to 1 Mbps. The hybrid gear train...

SKU: DF-DFR0645-G

The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...

SKU: SF-DEV-14629

The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from ...

SKU: SF-DEV-14346

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. Programming the ProtoSnap Plus is easy with the free Arduino software you’ll need to program the ATmega32...

SKU: LB-ETEXTILELED-G

This is a simple single unit GREEN E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. They’re even washable (with special care)!These are a thicker PCB than the Sparkfun Lilypad LEDs 

SKU: SF-DEV-09267

The LilyPad Accelerometer is a three-axis accelerometer based on the Analog Devices ADXL335, designed for the LilyPad wearable e-textile system. It detects joint movement, inclination, and vibration, outputting 0–3 V analogue signals on the X, Y, and Z axes. The board features large sewable pads...