All Products

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: DF-DRI0023

INTRODUCTION Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain......? As we all know, regular stepper motors are hard to drive, but with this stepper motor shield, you can easily drive 2 stepper motors vi...

SKU: DF-DRI0035

INTRODUCTION This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper motors (up to 2A per motor coil, 40V max). This stepper mo...

SKU: AF-2448

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel (3A peak). It's the same driver chip used in the Adafruit Motor Shield and Motor...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: DF-DRI0017

The DFRobot 2×2A Motor Shield uses the L298P dual full-bridge driver chip to control two 4.8–35 V DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 10 and 11 for speed control and digital pins 12 and 13 for enable/disable. The shield ...

SKU: DF-FIT0349

This bipolar stepper motor with planet gear box (gear ratio: 5.18) uses a standard 8mm-diameter D type output shaft, and has a 1.8° step angle (200 steps/revolution). Each phase draws 1.6 A at 2.78 V, allowing for a holding torque of 18kg-cm (176N-cm) (200rpm). The motor has a body dimension ...

SKU: EC-MCS02930M

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive the servo with arduino pin9 and pin10. Features Be able to drive 4 DC motor and...

SKU: DF-DRI0009

The DFRobot 2×2A DC Motor Shield uses the L298P dual full-bridge driver chip to control two DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 5 and 6 for speed control and digital pins 4 and 7 for enable/disable. The shield can be pow...

SKU: AF-3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: SF-ROB-14451

The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...

SKU: DF-DFR0406

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two DC motors with Arduino board as well as control the speed and direction of the ...

SKU: DF-FIT0708

A compact 10 mm micro stepper motor with 18° per step, designed for direct connection to microcontrollers like Arduino and ESP32 without requiring a dedicated driver board. The 2-phase 4-wire bipolar configuration makes it straightforward to integrate into small-scale automation projects. The mo...

SKU: SF-ROB-12859

The Big Easy Driver is a stepper motor driver board for bipolar stepper motors up to 2 A per phase, based on the Allegro A4988 driver chip. Designed by Brian Schmalz, it's the successor to the popular Easy Driver board. It defaults to 16-step microstepping mode and includes onboard 5 V and 3.3 V...

SKU: SF-ROB-13656

This NEMA 23 bipolar stepper motor delivers 125 oz·in of holding torque with 200 steps per revolution (1.8° step angle). Equipped with extra-long 600 mm AWG22 wires, it's designed for CNC applications where longer cable runs are needed. Stepper motors provide precise position control without the...

SKU: AF-6353 · MPN: ADA6353

The Adafruit STSPIN220 Stepper Motor Driver Breakout makes controlling bipolar stepper motors simple with a GPIO-only interface — just two pins (DIR and STEP) are all you need. It defaults to 1/16 microstepping and supports up to 1/256 microstepping via mode pin configuration, making it ideal for...

SKU: EC-CDP03051C

The Arduino CNC Shield V3.51 by Protoneer turns an Arduino Uno into a 4-axis CNC controller. Compatible with GRBL 0.9 firmware, it accepts Pololu-style stepper drivers (sold separately) and supports up to 4 stepper motors for CNC routers, laser cutters, 3D printers, and other precision motion pro...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-4411

A compact NEMA-8 bipolar stepper motor with the same 1.8° step angle (200 steps/revolution) as full-size NEMA-17 motors, but in a much smaller 20 × 30 mm package. Ideal for compact CNC builds, small robotics, and space-constrained motion control projects. This 4-wire bipolar stepper is rated for...

SKU: AF-2927

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Fem...