All Products

SKU: AF-1570 · MPN: 1570

A compact 3.7 V lithium-ion polymer (LiPo) battery with approximately 100 mAh capacity (0.4 Wh). Thin, lightweight, and powerful, this cell is suited for small wearable projects, IoT devices, and compact electronics where space is limited. The battery comes pre-wired with a genuine 2-pin JST-PH ...

SKU: TB-SB2300

A 14500-size rechargeable lithium-ion battery with 800mAh capacity and 3.7V nominal voltage. The 14500 form factor is the same size as a standard AA battery, making it a common choice for LED torches and other compact devices that accept this cell type. This cell has a nipple (button-top) positiv...

SKU: AF-653 · MPN: 653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: SF-GPS-26620 · MPN: GPS-26620

Built around the Quectel LG290P, this compact RTK GNSS breakout is designed for high-precision positioning projects that need quad-band, multi-constellation reception. It follows the same board dimensions, pin layout and connectors as SparkFun’s GPS-RTK-SMA Breakout - ZED-F9P (Qwiic), making it a...

SKU: AF-1870 · MPN: 1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: DF-DFR0424

INTRODUCTION The LightBlue Bean is a new Arduino compatible microcontroller with built-in Bluetooth LE support. It can be programmed wirelessly and is perfect for smartphone-controlled projects! With its low-cost and low-energy consumption, this little bean can handle almost everything y...

SKU: DF-DFR1236 · MPN: DFR1236

This development kit combines the FireBeetle 2 ESP32-C5 microcontroller board with a dedicated solderless IO expansion shield, giving you a practical platform for smart home and IoT prototypes.The ESP32-C5 brings dual-band Wi-Fi 6 on 2.4 GHz and 5 GHz, plus Bluetooth 5, Thread and Zigbee support....

SKU: AF-680 · MPN: 680

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground), they're as simple to use as a standard LED. The diffused lens provides an even...

SKU: AF-3672 · MPN: 3672

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, exploringcs.org) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and hum...

SKU: AF-80 · MPN: 80

A high-quality 9V battery clip with a pre-assembled 5.5mm/2.1mm centre-positive barrel connector. The moulded plastic clip covers the battery terminals to prevent short circuits, and the barrel plug connects directly to Arduino boards and other devices with a standard DC barrel jack. Key Feature...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...

SKU: DF-DFR0208

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo battery at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will wo...

SKU: AF-248 · MPN: 248

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells for 7.2V at ~2000mAh. The 9V alkaline output is ideal for boards with a 5V volta...

SKU: SF-PRT-11892

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The metal housing connects to the positive (+) side of the battery and the PCB pad underneath is connecte...

SKU: DF-DFR0498

DFRobot FireBeetle series are low power consumption development modules designed for Internet of Things (IoT). The FireBeetle Covers-Camera & Audio Media Board is a multimedia device for IoT that provides interfaces to connect NAU8822 CODEC IIS, OV7725 camera, SD card (SDIO), earphone and mic...

SKU: AF-1657 · MPN: 1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: AF-1329 · MPN: 1329

Connect a battery pack or bare wires to any device with a 2.1 mm DC barrel jack input using this adapter cable. Colour-coded alligator clips (red for centre-positive, black for ring-negative) clip onto battery terminals or exposed wires, while the moulded 2.1 mm barrel plug feeds power straight i...

SKU: DF-SEN0664 · MPN: SEN0664

Built around the Bosch BMP585 chip, this Gravity module measures barometric pressure and temperature for altitude, weather and environmental sensing projects. Its gel-filled cavity and industrial protective cover help it resist water, moisture and chemical exposure, making it better suited to dem...

SKU: AF-3403 · MPN: 3403

The Feather M0 Express is Adafruit's CircuitPython-optimised Feather, built around the ATSAMD21G18 ARM Cortex M0+ processor. It combines the standard Feather M0 platform with 2 MB of SPI flash storage, a Mini NeoPixel, and a UF2 bootloader for drag-and-drop programming — no special tools or drive...