All Products

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: SF-GPS-26620 · MPN: GPS-26620

Built around the Quectel LG290P, this compact RTK GNSS breakout is designed for high-precision positioning projects that need quad-band, multi-constellation reception. It follows the same board dimensions, pin layout and connectors as SparkFun’s GPS-RTK-SMA Breakout - ZED-F9P (Qwiic), making it a...

SKU: DF-DFR0424

INTRODUCTION The LightBlue Bean is a new Arduino compatible microcontroller with built-in Bluetooth LE support. It can be programmed wirelessly and is perfect for smartphone-controlled projects! With its low-cost and low-energy consumption, this little bean can handle almost everything y...

SKU: AF-653 · MPN: 653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: AF-1870 · MPN: 1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: SF-TOL-10829

This smart SMD tester is essentially a pair of multimeter tweezers. This allows you to troubleshoot circuits with small SMD parts without having to fumble with large probes or long wires. Test resistors, capacitors and diodes one-handed!Features:  Resistance Range: 300Ω/3KΩ/30KΩ/300KΩ ±(1.0%...

SKU: DF-DFR0998

This real-time clock (RTC) module uses the SD3031 chip, which has an integrated crystal oscillator and temperature compensator. This provides high-precision timing and stability. At a temperature of 25 °C, the accuracy is maintained at ±3.8ppm (±0.32832 seconds/day).The SD3031 can be powered by b...

SKU: LB-EAGLED-BUZZ

EagLED is Little Bird Electronics' wearable development kit: an Arduino-compatible microcontroller board with LEDs, a light sensor, push button and buzzer built into a snippable PCB for e-textile projects.Built-in USB support lets you program and power the board from a computer. It works with the...

SKU: AF-680 · MPN: 680

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground), they're as simple to use as a standard LED. The diffused lens provides an even...

SKU: AF-1657 · MPN: 1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: AF-1359 · MPN: 1359

These SMD testing tweezers are a built-in multimeter with tweezer-shaped probes — just grab a component to test it. No more fumbling with bulky multimeter probes on tiny 0402 or 0603 parts. Measure resistors, capacitors, diodes, and LEDs by simply pinching them between the tips. A scanning mode ...

SKU: DF-DFR1236 · MPN: DFR1236

This development kit combines the FireBeetle 2 ESP32-C5 microcontroller board with a dedicated solderless IO expansion shield, giving you a practical platform for smart home and IoT prototypes.The ESP32-C5 brings dual-band Wi-Fi 6 on 2.4 GHz and 5 GHz, plus Bluetooth 5, Thread and Zigbee support....

SKU: AF-80 · MPN: 80

A high-quality 9V battery clip with a pre-assembled 5.5mm/2.1mm centre-positive barrel connector. The moulded plastic clip covers the battery terminals to prevent short circuits, and the barrel plug connects directly to Arduino boards and other devices with a standard DC barrel jack. Key Feature...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...

SKU: AF-3296 · MPN: 3296

The Adafruit DS1307 Real Time Clock breakout keeps accurate time even when your microcontroller loses power or is reprogrammed. This battery-backed I2C RTC is one of the most widely used clock chips, making it a reliable choice for datalogging, alarms, timers, and clock projects. The DS1307 requ...

SKU: AF-3520 · MPN: 3520

A 3-pack of standard alkaline AAA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a capacity of approximately 1200mAh at a 25mA discharge rate. Specifications Type – AAA Chemistry ...

SKU: AF-5436 · MPN: 5436

A squishy silicone button module with a built-in PWM controller and colour-changing power indicator. Press to cycle through three power levels — 100%, 70%, and 35% duty cycle — with the illuminated power symbol glowing red, blue, or green to show the current setting. Long press for two seconds to...