All Products

SKU: DF-DFR0063

This is an 16x2 LCD display screen with with I2C interface. It is able to display 16x2 characters on 2 lines, white characters on blue background. Usually, Arduino LCD display projects will run out of pin resourceseasily, especially with Arduino Uno. And it is also very complicated with the wi...

SKU: DF-FIT0127

Standard 16x2 character LCD display. It has a basic 16 character by 2 line display with a blue background with white characters. You could get a compatible LCD pannel or IIC LCD backpack here. SPECIFICATIONS Supply voltage:5V DOCUMENTS Datasheet SHIPPING LIST 16x2 Character LCD...

SKU: DF-DFR0091

A 128 × 64 pixel graphic LCD module based on the ST7920 controller, featuring a blue backlight with white characters. Supports both parallel (8/4-bit) and SPI (3-wire serial) interfaces, with parallel mode set as the default. To switch to SPI mode, move the R9 resistor to the R10 position. The d...

SKU: SF-LCD-18160

This is a basic 16 character by two line display with a snazzy black background with white characters. This LCD utilizes the extremely common HD44780 parallel interface chipset. Interface code is freely available. This is the same LCD that is included with the SparkFun Inventor's Kit and comes wi...

SKU: AF-715

The Adafruit I²C Controlled + Keypad Shield Kit lets you drive a 16×2 character LCD and read 5 navigation buttons using only two I²C pins on your Arduino. This frees up the 9+ digital pins that a standard LCD connection would require, while still allowing other I²C devices to share the bus. The ...

SKU: DF-DFR0555

The Gravity I2C LCD1602 is a 16×2 character LCD display module with a blue backlight and white text. It communicates over I2C, requiring only two data pins instead of the many parallel connections of a traditional LCD1602. The module is compatible with both 3.3V and 5V systems, and the contrast i...

SKU: DF-DFR0464

A 16×2 character LCD module with full RGB backlight, communicating over I2C for minimal wiring. With support for 16 million backlight colours, this display adds a vibrant, customisable readout to your Arduino or compatible microcontroller projects using just four wires: VCC, GND, SDA, and SCL. P...

SKU: AF-398

A 16 × 2 character LCD with a full RGB backlight, displaying black text on a customisable colour background. Set the backlight to any colour — red, green, blue, purple, teal, white, or anything in between — by controlling three independent LED channels. With excellent daylight readability and vib...

SKU: DF-DFR0374

The Arduino LCD Keypad Shield V2 includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD and Analog Pin 0 is used to read the work status of five pushbuttons. This product ensures consumer's convience especially when comp...

SKU: SF-LCD-16397

The SparkFun 16×2 SerLCD is a serial-enabled LCD that provides a simple, cost-effective way to add an RGB-on-black liquid crystal display to your project. An on-board ATmega328P microcontroller handles all screen control, eliminating the need for a separate backpack board. The display supports t...

SKU: AF-716

This Arduino shield kit combines a 16×2 RGB character LCD with five navigation buttons, all controlled over I2C using just two pins (Analog 4 and 5). An on-board I2C port expander handles the LCD, RGB backlight, and keypad inputs, leaving your remaining pins free for sensors and other peripherals...

SKU: TB-XC4454

This Arduino-compatible LCD shield combines a 16×2 character LCD display with a six-button keypad on a single board. The backlit display and built-in navigation buttons (up, down, left, right, select, and reset) make it easy to create user-friendly menus and interfaces for your Arduino projects. ...

SKU: AF-714

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a...

SKU: DF-DFR0009-BP

This is the back panel pcb of 1602 Arduino LCD Shield. This shield allows you to place your own LCD onto this shield. It only requieres a 16x2 HD44780 compatible LCD. This Shield uses Arudino LCD4Bit library. The pcb is compatible with the following LCD: Basic 16x2 Character LCD -...

SKU: SF-LCD-00709

This is a basic 16 character by 2 line display with a snazzy black background with white characters. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes white...

SKU: PR-PIM094

This is the lovely little 16 x 3 character LCD we use on Display-O-Tron.A super-slim alternative to the classic industrial character displays. This model has a transparent display allowing you to add your own back-light if you wish! High-contrast LCD display 3 x 16 characters (3.6mm character hei...

SKU: DF-FIT0021

A 128×64 pixel graphic LCD module driven by the ST7920 controller. This display supports English characters, Chinese characters, and custom graphics over both serial (SPI) and parallel interfaces, making it a versatile choice for Arduino projects that need more than a simple character display. T...

SKU: DF-DFR0936

This shield with a 16×2 RGB LCD screen could bring you a brand-new experience with an LCD screen!The RGB LCD shield extends all IOs of Arduino UNO on the back, by which you can connect with modules like sensors, LEDs, and servos while using this screen to display content. More possibilities for y...

SKU: DF-DFR0154

A 20×4 character I2C LCD display module compatible with Arduino and other microcontrollers. It shows white characters on a blue backlit background, and the I2C interface means you only need two data pins (SDA and SCL) instead of the six or more required by a standard parallel LCD. The module sup...

SKU: AF-3128

The Adafruit 0.54" Quad Alphanumeric FeatherWing Display in blue adds a bright, 4-character 14-segment LED display to any Feather board. Each character can display letters, numbers, and symbols, making it ideal for clocks, status indicators, sensor readouts, and more. Driven by the HT16K33 I2C m...