All Products

SKU: AF-2107 · MPN: 2107

The Adafruit USB Isolator provides galvanic isolation between your computer's USB port and connected devices, protecting against harmful noise, ground loops, surges, and voltage spikes. Based on Analog Devices' USB isolator technology, it supports both Low Speed (1.5 Mbps) and Full Speed (12 Mbps...

SKU: DF-FIT1019 · MPN: FIT1019

Protect sensitive USB ports from external power interference and signal noise with this industrial-grade USB 2.0 isolator. It uses magnetic isolation to create an electrical barrier between connected USB devices, helping to reduce ground loop issues and protect development boards, motherboards an...

SKU: DF-FIT0860

This small portable USB isolator with USB2.0 compatibility provides complete isolation between devices.  Featuring a 12Mbps data transmission rate and 2500V isolation voltage, the industrial USB isolator can be used to protect the USB port of all kinds of devices without connecting exter...

SKU: AF-4903 · MPN: 4903

This compact breakout provides electrical isolation between two sides of an I2C bus, helping separate earth-grounded circuits, reduce noise, or protect sensitive low-voltage monitoring equipment from faults cascading across the bus.The ISO1540 is fully bidirectional, supports clock stretching, an...

SKU: DF-TEL0190 · MPN: TEL0190

RainbowLink V2 is a pocket-sized USB Type-C serial debugging workstation that combines four independent communication channels with useful field power outputs. It replaces multiple USB dongles for RS485, RS232 and TTL UART work, making it well suited to field engineering, IoT development and indu...

SKU: DF-DFR0886 · MPN: DFR0886

Built around the ESP32 dual-core processor, the Edge101 is an industrial IoT controller for taking ESP32 and Arduino-based projects beyond the workbench and into real-world automation, monitoring and edge gateway deployments.It combines isolated RS485 with Modbus compatibility, isolated CAN bus, ...

SKU: AF-3785 · MPN: 3785

This isolated PoE splitter takes a unified Power over Ethernet signal from a single RJ-45 cable and separates it into data (Ethernet) and regulated 5V DC power via a Micro USB plug. It works with any 802.3af-capable router or switch, letting you power non-PoE devices over a standard Ethernet run ...

SKU: DF-DFR0504

The Analog Signal Isolator can isolate analog signal and provide isolated power to sensors. It can effectively prevent sensor signal interference and apply to multi-parameter water quality monitoring sensors. Because usually sensors will be interfered by the other sensors during the measurement,...

SKU: WS-23949

The USB to RS485/422 is an industrial-grade isolated converter designed for reliable and stable communication. Featuring an original FT232RL chipset and SP485EEN transceiver, it ensures fast, interference-free data transmission. The unit includes multiple protective circuits such as power isolati...

SKU: AF-4552 · MPN: 4552

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then sepa...

SKU: AF-3848 · MPN: 3848

An isolated Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.8 A. The built-in isolation transformer ensures there is no direct electrical connection between the Ethernet side and the 5 V output — important for safet...

SKU: AF-5871 · MPN: ADA5871

The Adafruit TS3USB30 is a 1-to-2 USB switch breakout board that lets you connect one of two USB peripheral devices to a single USB host port. Based on the TI TS3USB30, it handles high-bandwidth USB 2.0 connections up to 480 Mbps — ideal when you need to switch between two USB devices without usi...

SKU: AF-5954 · MPN: ADA5954

The Adafruit TRRS Trinkey is a USB-A plug-in microcontroller designed specifically for assistive technology. It combines an ATSAMD21 processor with a switched TRRS 3.5mm audio jack, connecting all 6 jack pins (tip, ring 1, ring 2, sleeve, plus tip switch and ring 1 switch) to analog-capable GPIO ...

SKU: AF-5807 · MPN: ADA5807

This breakout is built around the HUSB238 USB PD sink chip, making it easy to negotiate power from a USB Type-C Power Delivery source without soldering tiny resistors. It plugs into a USB-C cable and uses the CC lines to request a suitable PD voltage.You can configure it with solder jumpers for f...

SKU: PH-106133 · MPN: 106133

The Power Bank KeepAlive (USB-C) prevents power banks from automatically shutting off when connected to low-power devices. It uses a 555 timer circuit to pulse a small amount of current through the USB-C port, keeping the power bank active even when drawing minimal power. This assembled SMD vers...

SKU: AF-5972 · MPN: ADA5972

The Adafruit Switchable USB Type A to C Breakout Board lets you individually enable or disable each of the four USB wires (V+, D+, D−, GND) using an onboard 4-position DIP switch. This makes it a versatile tool for USB debugging, charge-only configurations, and power monitoring. Key Features 4...

SKU: AF-2264 · MPN: 2264

The Adafruit FT232H Breakout turns your computer into a versatile interface for hardware protocols. Using the FTDI FT232H chip with its multi-protocol synchronous serial engine, you can communicate directly with I2C, SPI, JTAG, and serial UART devices — plus read and write digital GPIO pins — all...

SKU: AF-2778 · MPN: 2778

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 12V powered devices with a center-positive 2.1mm DC barrel jack from a USB port....

SKU: AF-259 · MPN: 259

This is a Lithium Ion and Lithium Polymer battery charger based on the MCP73833. It uses a USB mini-B for connection to any computer or 'USB wall adapter'. Charging is performed in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-volta...

SKU: AF-5997 · MPN: ADA5997

The Adafruit CH334F Mini 4-Port USB Hub Breakout converts one USB host port into four downstream ports using the CH334F USB 2.1 hub chip. Designed to be compact and embeddable, it fits inside enclosures or existing devices where a standard USB hub would be too bulky. The upstream connection can ...