All Products
Showing 1-20 of 81 products · 19 unavailable products hidden
Thumbnail Sized DC Motor Driver 2x1.5A (HR8833)
INTRODUCTION This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are ...
SimpleFOCmini Brushless DC Motor Driver Board
·
This compact DFRobot driver board is made for precise control of brushless DC motors using Field-Oriented Control (FOC). At just 26 x 21.5mm, it is well suited to tight builds where smooth motion, low noise and responsive control matter.SimpleFOCmini supports closed-loop control of motor position...
2x7A DC Motor Driver
An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...
Arduino Quad DC Motor Driver Shield
INTRODUCTION The latest quad motor driver shield for Arduino, compatible with 5V/3.3V Arduino controller, can control up to four DC motors with 8 pins at the same time. The shield supports PWM speed control and polarity control. The driver shield includes two TB6612FNG ...
15A Single DC Motor Driver
The DFRobot DRI0042 is a compact, high-current DC motor driver capable of continuously driving a single motor at up to 15A (with heatsink) from a 12–36V supply. The onboard LM2575 regulator provides a 5V 500mA output for powering an Arduino or other controller, and all control signal inputs inclu...
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
2x1.2A DC Motor Driver (TB6612FNG)
The DFRobot 2×1.2A DC Motor Driver is a compact dual-channel motor driver based on the TB6612FNG IC. It requires only four GPIO pins to control two DC motors, using the same control logic as the DFRobot L298N motor driver — making existing L298N code directly compatible. Each channel delivers up...
PPM 2x3A DC Motor Driver
This motor driver module is a special PPM signal motor controller for Aero modelling remote control. It is designed by DFRobot and it can be controlled by RC transmitter. The driver can convert PPM signal to the motor speed and direction control signal. There are two signal receiving chan...
DC Motor Driver HAT(V1.0)
The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...
MP6550 Single Brushed DC Motor Driver Carrier
The MP6550 from Monolithic Power Systems (MPS) is an H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 1.8 V to 22 V. It can supply up to about 1.7 A continuously and features configurable current sensing and current limiting. Since this board is a car...
2x3A DC Motor Driver Carrier Board for UNIHIKER M10
·
This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....
Dual-Channel DC Motor Driver-12A
This is a dual channel DC motor driver with an extremely small size of of 1.97”×1.97”×0.49”. The module comes with two motor channels that can drive two motors simultaneously, and each channel employs an indicator to show the rotation direction of the motor: blue is forward rotation, red is rever...
Cytron MOTION 2350 Pro RP2350 Robotics Controller
·
Built around Raspberry Pi’s RP2350 processor, this Cytron robotics controller is made for beginner and intermediate builders who want to create more advanced robots while spending less time on the supporting electronics.The board integrates a 4-channel brushed DC motor driver, servo outputs, GPIO...
DFRobot DFR1216 Expansion Board for UNIHIKER M10/K10 & micro:bit
·
This multi-function expansion board adds power, I/O and drive capability to UNIHIKER M10/K10 and micro:bit projects. It is designed for mobile robots, portable interactive builds and maker projects that need more connectivity than the main controller can provide on its own.The board expands your ...
Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board
·
The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...
Cherokey: 4WD Arduino Mobile Robot
The Cherokey 4WD arduino mobile robot is a versatile mobile robot jeep compatible with the most popular microcontrollers like DFRduino UNO R3 - Arduino Compatible, Mega2560 (arduino microcontroller board), Romeo V2(an Arduino Robot Board (Arduino Leonardo) with Motor Driver)...etc. Cherokey e...
Romeo V2- Arduino Robot Board (Arduino Leonardo) with Motor Driver
RoMeo V2 [R3] is an All-in-One Arduino based robot board, it is especially designed for robotics applications, and extended devices. Romeo benefits from the Arduino open source platform, it is supported by thousands of open source projects, and can easily be expanded with Arduino Shields. The ...
Gravity: IO Expansion Motor Driver Shield
Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and TB6612FNG dual motor driver. It also has XBee socket, I2C interface and UART po...
SparkFun Qwiic Motor Driver
The SparkFun Qwiic Motor Driver takes all the great features of the Serial Controlled Motor Driver (SCMD) and miniaturizes them, adding Qwiic ports for plug and play functionality. Boasting the same 4245 PSOC and 2-channel motor ports as the SCMD, the SparkFun Qwiic Motor Driver is designed to co...
SparkFun Auto pHAT for Raspberry Pi
The SparkFun Auto pHAT is an all-in-one robotics add-on for the Raspberry Pi. It drives up to two DC motors (with optional encoder support) and four servo motors, all controlled over I2C — leaving your Pi's GPIO pins free for other uses. A Qwiic connector is included for easy expansion. The boar...
