All Products

SKU: AF-3416

The Adafruit 16-Channel PWM/Servo Bonnet adds precision servo and PWM control to your Raspberry Pi. Using the PCA9685 I2C PWM controller, it drives up to 16 servos or PWM outputs simultaneously with 12-bit resolution — completely free-running with no Pi processing overhead. Up to 62 bonnets can ...

SKU: AF-2327

The Adafruit 16-Channel PWM/Servo HAT adds precision servo and PWM control to your Raspberry Pi. Using the PCA9685 I2C PWM controller, it drives up to 16 servos or PWM outputs simultaneously with 12-bit resolution — completely free-running with no Pi processing overhead. Up to 62 HATs can be sta...

SKU: AF-1427

The Adafruit 16×8 LED Matrix Driver Backpack is a breadboard-friendly breakout for the HT16K33 multiplexed LED driver. Unlike the pre-configured LED backpacks, this version breaks out all 16 anode and 8 cathode pins, letting you wire up any LED matrix configuration you need — up to 128 individual...

SKU: AF-2946

The Adafruit IS31FL3731 breakout is a charlieplexed PWM LED matrix driver that controls a 16×9 grid of individually dimmable LEDs over I2C. Each of the 144 LEDs can be set to any brightness level with 8-bit (256-level) PWM — no complex wiring or constant signal sending required. The IS31FL3731 o...

SKU: AF-802

The Adafruit 1.8" Colour TFT Shield is a plug-and-play display solution for Arduino, combining a bright 128×160 pixel TFT screen with a microSD card slot, 5-way joystick navigation switch, and three tactile buttons. This R3-format shield works with any Arduino or Metro board including the Metro M...

SKU: AF-5394

The Adafruit 1.9" TFT is a wide-format IPS display featuring 320×170 pixels at 16-bit colour with viewing angles up to 80° in any direction. Driven by the ST7789 chipset over 4-wire SPI, this breakout works with any microcontroller — even those with limited memory and GPIO. An onboard 3.3V regul...

SKU: AF-4947

The Adafruit 2.13" Tri-Colour eInk Display brings electronic paper technology to your microcontroller projects. Featuring a 250×122 pixel display with black, red, and white ink, this breakout delivers high-contrast, daylight-readable visuals that persist even when power is completely disconnected...

SKU: AF-4814

The Adafruit 2.13" HD Tri-Colour eInk FeatherWing brings electronic paper technology directly to your Feather board. Featuring a 250×122 pixel display with black, red, and white ink, this FeatherWing delivers high-contrast, daylight-readable visuals that persist even when power is completely disc...

SKU: AF-6383 · MPN: ADA6383

E-Ink and ePaper panels are excellent for low-power projects where you want a daylight-readable display that can hold its image even when power is disconnected. This bare 2.13" diagonal panel gives you a paper-like, high-contrast readout for labels, badges, status screens, data displays and other...

SKU: AF-4687

The Adafruit 2.13" Monochrome E-Ink Bonnet brings crisp, paper-like displays to your Raspberry Pi with no soldering required. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying high-contrast black-and-white graphics that remain visible even with power discon...

SKU: AF-4197

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its image even with power completely disconnected — just like printed paper. An onbo...

SKU: AF-4567

The Adafruit 2.23" Monochrome OLED Bonnet gives your Raspberry Pi a bright, high-contrast display that's easy to read from across the room. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying sharp white text, graphics, and animations at up to 30 FPS. With 1...

SKU: AF-1429

Control 24 channels of 12-bit PWM output with the Adafruit TLC5947 breakout board. Designed for LED control, this SPI-driven board delivers constant-current open-drain outputs that keep brightness consistent even if the power supply dips. The chainable design lets you connect as many boards as yo...

SKU: AF-5146

The Adafruit 24LC32 I2C EEPROM Breakout provides 32 Kbit (4 KB) of reliable, non-volatile storage over a simple I2C interface. Store calibration values, MAC addresses, access tokens, or any data that needs to persist through power cycles and firmware updates — without the page-write constraints o...

SKU: AF-4777

Add a versatile grayscale eInk display to your Feather project with this 2.9" FeatherWing. The 296×128 pixel panel supports four levels of grey — white, light grey, dark grey, and black — giving you more visual depth than a standard monochrome display while refreshing in about one second, far fas...

SKU: AF-1028

Add a large, vibrant tri-colour eInk display to your microcontroller project with this 2.9" breakout board. The panel displays red, black, and white pixels at 296×128 resolution that remain visible even with power completely disconnected — just like printed paper, but with the added impact of col...

SKU: AF-5825 · MPN: ADA5825

This square TFT module is for advanced display projects that need a high-resolution, 3.4 inch IPS panel with a 480 x 480 pixel layout. It delivers 16-bit full-colour output and wide off-axis viewing, making it a neat fit for compact dashboards, controls and custom embedded interfaces.The display ...

SKU: AF-5808 · MPN: ADA5808

This square TFT module is made for advanced display projects that need a high-resolution, compact screen. It has a 3.4 inch IPS panel with 480x480 full-colour pixels, giving a crisp square format with good colour visibility off-axis.The display uses an ST7701S driver with SPI for configuration an...

SKU: AF-3106

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in blue. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall blue 7-segment display with decimal points and a centre colon for clock displays. ...

SKU: AF-3088

The Adafruit 4-Digit 7-Segment LED Matrix Display FeatherWing makes it easy to add a numeric display to any Feather project. The HT16K33 driver handles all LED multiplexing over I2C, so your Feather only needs two shared pins — leaving all other GPIO free for sensors, buttons, and additional disp...