All Products

SKU: DF-DFR0076

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefighting robots, fire alarm projects, and other safety applications. The Gravity i...

SKU: SF-SEN-19018

An Infrared detector is a detector that reacts to infrared (IR) radiation. These simple devices operate at 940nm and work well for generic IR systems including remote control and touch-less object sensing. Using a simple ADC on any microcontroller will allow variable readings to be collected from...

SKU: DF-SEN0204

A non-contact liquid level sensor that detects the presence of liquid through a container wall — no direct contact with the liquid required. Using advanced signal processing via the XKC-Y25-T12V chip, it works through most non-metallic containers including plastic, glass, and ceramic. This makes...

SKU: DF-SEN0678 · MPN: SEN0678

This Gravity air quality module uses Sensirion’s STCC4 gas sensing chip to directly measure carbon dioxide with the thermal conductivity measurement principle. It is designed for compact, cost-effective indoor monitoring nodes where stable CO₂ readings are needed without complex hardware integrat...

SKU: DF-SEN0127

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in consumer and industry markets. It has a high sensitivity and fast response time. ...

SKU: DF-SEN0518

The DFRobot Gravity MAX30102 sensor module measures heart rate and blood oxygen saturation (SpO2) using photoplethysmography (PPG). It integrates the Maxim MAX30102 chip with an on-board MCU that processes raw PPG data and outputs heart rate and SpO2 values directly via I2C or UART, reducing proc...

SKU: DF-FIT0511

The Gravity 4Pin Sensor Adapter converts 4-pin sensors to the DFRobot Gravity interface, making it easy to connect compatible sensors to Gravity-enabled controllers. Features a press-type terminal for quick, tool-free wire connections. A 3.3V/5V power switch provides flexibility for different se...

SKU: DF-SEN0470

A factory-calibrated electrochemical sulfur dioxide (SO2) sensor with I2C, UART, and analogue output modes. Part of the DFRobot Gravity gas sensor series, this module quickly and accurately measures SO2 concentration for industrial monitoring and environmental protection applications. The electr...

SKU: SF-SEN-10266

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP382 is a miniaturized receiver for infrared remote control systems. A PIN d...

SKU: DF-SEN0128

An analogue alcohol gas sensor based on the MQ-3 probe, designed for use with Arduino and other microcontrollers. The sensor outputs a voltage proportional to the concentration of alcohol vapour in the surrounding air, making it suitable for breathalyser-style projects, air quality monitoring, an...

SKU: DF-TEL0180 · MPN: TEL0180

The Gravity: WiFi IoT Module is a companion accessory for the Gravity: Science Data Acquisition (SCI DAQ) Module, enabling wireless sensor data transmission to IoT platforms without any programming required. Simply connect sensors to the SCI DAQ module and start uploading data instantly. Operati...

SKU: DF-SEN0189

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...

SKU: DF-DFR0646-G

An 8-digit green LED segment display module with I2C communication, part of the DFRobot Gravity sensor and module range. It provides a clear, bright numerical display with 16 levels of adjustable brightness, making it easy to show sensor readings, counters, clocks, and other numerical data in you...

SKU: DF-DFR0021-W

A simple digital white LED module with Gravity interface. Plugs directly into DFRobot IO/Sensor expansion shields for easy integration with Arduino projects — ideal for beginners learning digital output control. Specifications Type – Digital Colour – White Interface – Gravity 3-pin (Signal, ...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...

SKU: DF-DFR0300

The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring water quality, nutrient levels in hydroponic systems, and soil salinity in agricultu...

SKU: DF-SEN0209

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printe...