All Products

SKU: DF-DRI0041

An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...

SKU: DF-ROB0124

The HCR (Home Care Robot) is a full-metal open-source mobile robot research platform designed for robotics research and service robot application development. Equipped with three high-torque omni wheels with encoders, it is capable of omnidirectional translational and rotational motion. The plat...

SKU: AF-727

A slim 3×AAA battery holder with a built-in on/off switch and JST 2-pin connector. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery connector. Uses a genui...

SKU: SF-PRT-12639

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an additional channel — commonly used for microphone input on hands-free headsets or video ...

SKU: SF-CAB-10215

A standard USB 2.0 Type-A to Micro-B cable, 1.8 m (6 ft) in length. Micro USB is the standard connector found on a wide range of development boards, microcontrollers, and electronics accessories. Key Features USB 2.0 Type-A to Micro-B – Standard 5-pin micro USB connector 1.8 m Length – Genero...

SKU: AF-1859

This 2.4"/61mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Antenna comes with a SMA connector, which is the most common type you'll see for Cell...

SKU: AF-3372

The Espruino Puck.js is a low energy Bluetooth smart button that can be programmed and debugged wirelessly with JavaScript. It is both multi-functional and easy to use, with a custom circuit board, the latest Nordic chip, Bluetooth LE, NFC, magnetometer, temperature sensor, RGB LEDs,&n...

SKU: SF-PRT-10462

Nylon standoffs for mounting PCBs in enclosures or elevating boards off work surfaces. These ¾" (19mm) long standoffs are tapped for 4-40 screws and sold in a pack of 10. Key Features Nylon Construction – Non-conductive, won't short circuit boards 4-40 Thread – Standard tapping for 4-40 screw...

SKU: AF-67

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...

SKU: SF-PRT-10512

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Features Snap-In Design – Battery clicks securely into place 5.5mm/2.1mm Barrel...

SKU: AF-3287

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...

SKU: AF-3286

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery...

SKU: PL-1960

Steel zinc-plated pan-head Phillips machine screws, #4-40 thread, ¼" (6.35mm) long. Sold in a pack of 25. Ideal for securing PCBs, standoffs, and enclosures in electronics projects. Specifications Thread: #4-40 Length: ¼" (6.35mm) Head Type: Pan-head, Phillips drive Material: Steel, zinc-pl...

SKU: SF-PRT-10739

Metal short standoffs: 3/8" long x ¼"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don’t forget the screws! Related below. Note: These are sold as a set of ten.

SKU: TB-MP3312

This 12W switchmode plug pack features manually selectable voltage output (3V, 5V, 6V, 7.5V, 9V, or 12V DC) at up to 1000 mA, plus a built-in USB-A output socket for charging or powering USB devices. It comes with 7 interchangeable DC plugs to suit a wide variety of barrel connector sizes. The s...

SKU: SF-PRT-10898

A pack of 100 premium female-to-female jumper wires, 155 mm long. Use these to connect any male header to another male header on breadboards, development boards, and breakout modules. Multiple jumpers can be installed side by side on standard 0.1" pitch headers. Specifications Connector Type –...

SKU: SF-DEV-10914

It’s blue! It’s skinny! It’s the Arduino Pro! SparkFun’s minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower than other Arduino development boards, it may not be compatible with many Arduino shields which we...

SKU: SF-CAB-13191

A 4-pack of cables with an alligator clip on one end and a bare hookup pigtail (male pin) on the other. These cables make it easy to connect alligator clips directly into breadboards, development boards, and any standard 0.1" pin header. Key Features Alligator Clip to Male Pigtail – Clip one e...

SKU: SF-CAB-13244

A short 150 mm (6″) USB 2.0 Type-A to Micro-B cable, ideal for connecting development boards, chargers, and other devices within compact enclosures where a full-length cable isn't needed. Specifications Connector A – USB Type-A (male) Connector B – Micro-B 5-pin (male) Standard – USB 2.0 Le...

SKU: AF-3173

A simple, solder-on terminal block set sized to fit Adafruit Feather boards and FeatherWings. These 0.1″ pitch terminal blocks let you make secure, screw-down wire connections without soldering wires directly to your board — making projects easier to build, maintain, and modify. Compatible with ...