All Products

SKU: AF-382

A Zero Insertion Force (ZIF) socket for DIP chips of up to 28 pins and 0.3" width. The lever mechanism allows you to insert and remove chips without applying force, preventing bent or damaged pins. Lift the lever to open, drop the chip in, and push the lever down to latch it securely. The socket...

SKU: AF-2770

The 2.8" TFT Display is a bare LCD module with a capacitive single-touch touchscreen. Featuring 240×320 resolution with individual RGB pixel control and a bright 4-LED backlight, it delivers vivid full-colour output for custom projects. The display is driven by the ILI9341 chipset and the touchs...

SKU: AF-1774

The 2.8" TFT Display with Resistive Touchscreen is a bare LCD module featuring 320×240 resolution with individual RGB pixel control. Driven by the ILI9341 chipset, it supports SPI (3- or 4-wire), 8-bit parallel, and 16-bit parallel interfaces. The resistive touchscreen is an analogue type that r...

SKU: AF-1651

The 2.8" TFT Touch Shield with Resistive Touch Screen plugs directly into any Arduino UNO or Mega-shaped board, providing a bright, full-colour display with touch input and an onboard MicroSD card socket. Fully assembled and ready to use — no wiring or soldering required. This shield uses SPI fo...

SKU: EC-AMS320240TFT

The 2.8" TFT Touch Shield V4.3 is an Arduino-compatible display shield featuring a 240×320 colour LCD with a resistive touchscreen and onboard SD card socket. It communicates over SPI, keeping pin usage low and leaving more pins available for other components. Driven by the ILI9341 controller, t...

SKU: PL-1094

A miniature low-power 6V brushed DC gearmotor with a 297.92:1 metal gearbox. With a 10 × 12mm cross section, this micro metal gearmotor delivers useful torque in an extremely compact form factor. The D-shaped output shaft is 3mm in diameter and extends 9mm from the gearbox. Key Features 297.92...

SKU: LB-LS5508

A 2×AA battery holder with a protective cover, built-in on/off switch, and large alligator clip leads. The alligator clips make it easy to connect to circuits, components, and conductive materials without soldering — ideal for quick prototyping and classroom projects. Key Features 2×AA Capacit...

SKU: AF-245

The 2-Axis Joystick provides analogue input for your projects using two independent 10K potentiometers — one per axis. It reports position as either voltage or resistance, making it compatible with a wide range of microcontrollers including Arduino and Raspberry Pi. The modular form factor plugs...

SKU: DF-DFR0911

The 2-Channel Level Converter translates 12V signals down to 3.3V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 3.3V microcontrollers like Arduino. It supports common anode, common cathode, and differential signal inputs with PNP output (NPN to P...

SKU: DF-DFR0912

The 2-Channel Level Converter translates 12V signals down to 5V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 5V microcontrollers like Arduino. It supports common anode, common cathode, and differential signal inputs with PNP output (NPN to PNP c...

SKU: WS-19979

The 2-Channel RS232 Module for Raspberry Pi Pico converts UART signals to RS232 and vice versa using the SP3232EEN transceiver. It plugs directly onto the Pico via the onboard female pin header — no wiring required. The module provides two independent RS232 channels with TVS and ESD diode protec...

SKU: WS-24468

The Waveshare Barcode Scanner Module (C) is a compact 2D codes scanner module that uses intelligent image recognition to decode 1D and 2D barcodes from both paper and screens with high accuracy and speed. Featuring USB and UART interfaces, the module can be plugged directly into a computer or ea...

SKU: EC-RPA05036T

The 2-in-1 TF Card Dual System Switcher lets you install two MicroSD (TF) cards on a single Raspberry Pi and switch between them using a physical toggle. This allows you to run two different operating systems and swap between them without removing or swapping cards. The switcher can also be cont...

SKU: WS-19888

The Waveshare Pico-LCD-2 is a 2-inch IPS LCD display module designed to plug directly onto a Raspberry Pi Pico via its onboard female pin header. With 320×240 resolution and 65K RGB colours, it delivers clear, vibrant visuals for your Pico projects. The module uses an SPI interface requiring min...

SKU: DF-SER0050

The DFRobot 2Kg 180° Clutch Servo features built-in clutch protection and electronic overload protection, making it ideal for robotics and model applications where servos may encounter external forces or stalling. When external forces change the servo's angle during operation, the clutch functio...

SKU: DF-SER0056

The DFRobot 2Kg 300° Clutch Servo features built-in clutch protection and electronic overload protection, making it ideal for robotics and model applications where servos may encounter external forces or stalling. When external forces change the servo's angle during operation, the clutch functio...

SKU: DF-C-PCB-003

Get your custom PCB designs professionally fabricated with this 2-layer PCB service. You will receive 10 PCBs per order, with a maximum board size of 10cm × 15cm. Quantity is in multiples of 10 — add more to your cart if you need additional boards. Once your order is placed, email your design fi...

SKU: DF-FIT0730

The 2-Megapixel USB Night Camera features a Sony IMX291 sensor with exceptional low-light performance down to 0.0001 Lux. It delivers 1920×1080 video at 30fps (MJPG) and includes a built-in digital microphone that captures audio within a 5-metre range. The camera is driver-free (UVC compliant), ...

SKU: AF-366

These 2 mm pitch 10-pin socket headers are designed specifically for XBee modules, which use 2 mm pin spacing instead of the standard 2.54 mm (0.1″) pitch. Each pack includes two sockets — one for each side of the XBee module. Solder these sockets onto your PCB or breadboard adapter to create a ...

SKU: SF-PRT-10112

This 2 mm pitch 10-pin header mates with 2 mm XBee sockets and is ideal for creating custom breakout boards, "dummy" XBee modules for testing, or any project requiring 2 mm pitch pin headers. Key Features 2 mm Pitch – Matches XBee socket spacing 10 Pins – Compatible with standard XBee footpri...