All Products

SKU: DF-FIT0129

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in.

SKU: DF-DFR0382

An Arduino-compatible shield featuring a 4-digit 7-segment digital tube display (common cathode, 0.56") with 5 input buttons. Uses I2C to drive the display, providing an easy interface for menus, controls, and numeric readouts. The five onboard buttons (active on pin A0) can serve as menu select...

SKU: SF-GPS-23288 · MPN: GPS-23288

Bring high-precision GNSS positioning to your project with the u-blox NEO-F9P engine and dual-band L1/L5 reception. L5 signals sit in the protected ARNS band, helping reduce RF interference and improve reliability in challenging environments such as dense city streets.The breakout provides five s...

SKU: AF-419

Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flexible membrane material with an adhesive backing (just remove the paper) so you can attach it to nearly anything. The keys are connected into a m...

SKU: DF-DFR0600

PYNQ-Z2 is a FPGA development board based on ZYNQ  XC7Z020 FPGA, intensively designed to support PYNQ, a new open-sources framework that enables embedded programmers to explore the possibilities of xilinx ZYNQ SoCs without having to design programming logic circuits. Benefiting from progr...

SKU: AF-3845

This 3×4 matrix keypad provides 12 buttons (0–9, *, #) in a sturdy, rigid format. It uses a matrix scanning arrangement requiring only 7 pins to read all 12 keys, making it efficient to connect to Arduino, Raspberry Pi, and other microcontrollers. Header pins are included for breadboard use (som...

SKU: AF-1427

The Adafruit 16×8 LED Matrix Driver Backpack is a breadboard-friendly breakout for the HT16K33 multiplexed LED driver. Unlike the pre-configured LED backpacks, this version breaks out all 16 anode and 8 cathode pins, letting you wire up any LED matrix configuration you need — up to 128 individual...

SKU: SF-COM-15290

Keypads are very handy input devices, but who wants to tie up seven GPIO pins, wire up a handful of pull-up resistors, and write firmware that wastes valuable processing time scanning the keys for inputs? The SparkFun Qwiic Keypad comes fully assembled and makes the development process for adding...

SKU: SF-DEV-27873 · MPN: DEV-27873

This is a platinum-tier FPGA development board designed for high-speed performance in compact builds. Its low-profile backside has no components taller than 1.5mm, enabling the use of high-speed 1.5mm stack-height DF40 connectors for GTP-capable interfaces such as PCIe 2.0.At the centre is a Xili...

SKU: AF-5071

A premium milled and anodised aluminium enclosure for building a custom 4×4 mechanical keypad. The dark grey shell with silver accents provides a solid, professional-looking base for your macro pad or shortcut keypad project. The multi-part enclosure features a hinged design that lets you angle ...

SKU: AF-3983

Put your project in stealth mode with these super slim, super tiny, and silent Mini Soft Touch Push-button Switches. They're less 'clicky' than tactile switches, they have a rubbery elastomer that feels good to press. No dangly spider-leg-pins to solder as these buttons are SMD. We see these...

SKU: AF-5851 · MPN: ADA5851

This ultra-flexible LED strip packs 320 natural white SMT LEDs per metre into a slim 5 mm wide silicone-encased profile. The densely packed LEDs produce a smooth, continuous glow that resembles neon tubing — without expensive transformers or fragile glass. The thin silicone diffuser creates an ev...

SKU: AF-715

The Adafruit I²C Controlled + Keypad Shield Kit lets you drive a 16×2 character LCD and read 5 navigation buttons using only two I²C pins on your Arduino. This frees up the 9+ digital pins that a standard LCD connection would require, while still allowing other I²C devices to share the bus. The ...

SKU: DF-SEN0568

Fermion: MEMS Hydrogen Sulfide H2S Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery....

SKU: AF-4732

The 64×64 RGB LED Matrix with 3mm pitch features 4096 bright RGB LEDs in a 192×192mm panel. This high-density display offers a good balance between pixel density and panel size, suitable for indoor signage and video wall applications. This panel uses a non-standard 5-address (ABCDE) multiplexing...

SKU: AF-89

In 1970, John Conway came up with a 1-player game called Game of Life. The Game of Life is a mathematical game that simulates 'colonies' that grow or die based on how crowded or lonely they are and is known for the way it creates a beautiful organic display out of randomness.Here is a design for ...

SKU: AF-5687

Here at Adafruit, we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by this 'chip on board' ultra-flexible RGB LED Strip&nbsp;with a whoppin'&nbsp;630 SMT LEDs per meter (210 x&nbsp;RGB LEDs, with 3 in series per segment), soldered side-by-side&nbsp;and...

SKU: AF-5920 · MPN: ADA5920

A 1-metre flexible LED strip with 480 green SMT LEDs per metre, soldered side-by-side in a "chip on board" configuration. Topped with a translucent silicone diffuser and encased in a sealed silicone tube, the result is a continuous, smooth light output that resembles neon tubing — without the nee...

SKU: SF-DEV-13735

Blink any color you need! Use the LilyPad RGB LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can produce a broad variety of colors. Each of the colors in the RGB LED are connected to one of the sew tabs on the board labeled R, G, and B.The color channels on ...

SKU: AF-3963

So you've got your Adafruit NeoTrellis M4, a cool/witty name for your band, a Soundcloud account, a 3D-printed Daft Punk helmet... so what could be missing from your road to stardom?...The NeoTrellis M4 Enclosure, of course! A super-specifically laser-cut enclosure that turns your 'Trellis into a...